Question Locked

DVD drive not recognised or able to install in XP

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi all, hope someone can help,

I just fitted a brand new laptop DVD-RW drive to a Windows XP laptop. However, this drive is not recognised in the BIOS and XP can't install it. Device manager says a driver is not installed and the drive is unrecognised. Using Windows update does not help nor does allowing the Add Hardware Wizard to connect to windows update help. I've re-fitted this drive and re-booted numerous times with no difference being made.

Please could someone advise what I should do?

Specs: Lite-On DS-8A1P 021C DVD-RW laptop drive
OS: XP SP2

16 replies

by joq

Thanks for a swift response however, I've already tried this method of removing upper and lower filters which didn't help. I'm really puzzled by this one and can't think of anything else to try. Am I right in that optical drives use drivers found in XP and do not need seperate drivers installed?

by thumbsup2

If the BIOS is not seeing the drive, Windows can't install it. Did you check the jumper on the drive to make sure it was set exactly like the one you took out? If the old one was jumpered as Master, make sure the new one is too. Also make sure the IDE cable was plugged in correctly and that you didn't bend a pin.

You need to get it recognized in the BIOS first. Once that's done, in Windows, remove the "unrecognized device" from the device manager and reboot allowing Windows to see it again.

Where did you buy that drive? Lite-On in Europe doesn't list that model. They have lots that begin with the letters DH, but none have the letters DS.

It's sold in the USA.

http://us.liteonit.com/us/index.php?option=com_content&task=view&id=223&Itemid=88

by nepenthe0

I'm unable to provide [i]joq[/i] any further assistance, because I've never attempted to replace a laptop optical drive.

But I [b]know[/b] you can [i]do it[/i] 'cause you're so smart about everything...

Rick/Portland, OR

by thumbsup2

Category Optical Storage
Issue Drive not recognized
Problem Drive is NOT detected by PC

---------------------------------------------

? Solutions
[b]Drive NOT detected by BIOS[/b]

Check IDE connection in the back, make sure cable is securely attached at correct orientaion
Check jumper setting on the drive. There can only be 1 master device and 1 slave device on the same IDE channel

[b]Drive NOT detected in DOS environment[/b]

Please be sure to load DOS driver if you need to operate CD drives in DOS environment
Go to Download site to get DOS device driver

[b]Drive NOT detected in Windows environment[/b]

You do NOT need to load driver in Windows environment
Check your " IDE BUS controller " to ensure both IDE channel are enabled

by joq

Hi, thanks for the advice, but neither this drive or the old one has jumper settings. In device manager, it is listed as being on the secondary ide channel (HDD being master on the 1st channel). The drive name however, appears as jumbled up letters and lines (this is how it shows in the BIOS also).

by thumbsup2

If the old drive had the same type of problem, it's entirely possible the IDE controler on the MB (or the cable itself) is bad.

Have you tried removing the device in the device manager and rebooting?

by nepenthe0

I had no idea that optical drives wore [i]jumpers[/i] - that style went out of fashion years ago...

Rick/Portland, OR

by thumbsup2

Haven't you seen the kids wearing stuff that we thought was "cool" back in the 70's? Remember the "hip-huggers", leather vests and, of course, "flower power"? :D

by nepenthe0

The kids here all wear jeans and carry skate boards when they're not zooming down the middle of the street. When I was a tot, kids were sent home from school for wearing tennis shoes...

Rick/Portland, OR

by thumbsup2

In my day, females were required to wear dresses. Skirts could be worn if we went to a ball game. Males were required to wear slacks and a nice shirt. Tennis shoes were only allowed in gym class.

Out here, the kids don't bother with the jeans and skate boards. They've got tennis shoes with skates built into the heals, going up and down the sidewalks (or streets), zooming in and out of traffic as if they don't have a care in the world. And, forget about trying to get through Safeway or any department store (the big W in particular) without getting run over by them.

by joq

The old drive stopped working. It was installed and detected, but stopped reading any kind of disc. Not been able to test the cable as since it's a laptop, the case is close to impossible to open up. If it's the MB controller, then how would I test for it?

by thumbsup2

You can plug in a 3rd drive that is known to be good in another machine. There's always the chance that your new drive is deffective. Of course, you could reverse this and test your new drive on another machine that is known to be good.

If that's not possible, I would suggest you take the laptop to a service center for testing. As you've noticed, opening the case can be a real bugger. If it's under waranty, be sure to take it to an AUTHORIZED service center.

And, another thought based on what you just said about not being able to check the cable. It appears this is one of the drives that you simply slide into a slot on the laptop and the connection is made automatically for you. You don't have to mess with cables, correct? Have you tried unplugging the drive (remove it), rebooting a couple of times, then plugging the drive back in and booting up a last time? Multiple reboots without the drive helps Windows "clear it's throat".

I also have to ask.... you ARE turning off the computer, removing the battery and unplugging the cord while you're changing this device out, right? You're not trying to do this while it's running are you?

Have you looked at the back of the drive? Can you see any signs that it isn't plugging in correctly when you slide it into the slot? Does it snap into place? Can you see into the slot in the computer with a flashlight and detect any bent pins?

And, of course, the obvious. Are you sure this drive is designed for use on this particular laptop? Some manufacturer's design their cases so that ONLY their own replacement products can be used. The drive may SEEM to fit into the slot, but a connection somewhere may not be made properly.

Have you been into the BIOS to see if there's a way to get the BIOS to automatically detect the changed drive? What is the make and model of this laptop?

by joq

Thanks for the detailed response. I have been doing as you suggested, but I'll try again just incase. I'm quite sure the laptop should be able to accept the drive but the BIOS is very basic, hardly anything can be changed and no option for what you suggested.

The laptop is a MEDION MD420302 sometimes called MID 2020.

I looked for updated drivers from their site, but nothing newer. I thought about updating the BIOS as there is a newer verwion available however, it requires booting from cd in order to do this :( Going round in circles on this one, surely this can't be a totally uncommon event for people?

Thanks - off to double check things.

by thumbsup2

According to the manual for the MIM 2020, the BIOS have settings that can be changed. There are 6 categories across the top. Use the left/right arrow keys to move to another screen so that it does say that. You need to get to configuration setup screen. Then, use the up/down arrow keys to highlight the CD/DVD device. It should be set to auto or automatic. Once the device is highlighted, use the left/right arrow keys to change the selection. Press escape to exit that screen, then use the left/right arrow keys to move to Exit, save changes and exit.

Let's see if we can get this thing to auto-detect the device.

If it still fails to detect properly, it's highly probable the drive is defective and reporting garbage to the BIOS. Return it.

This discussion is closed to new replies.