Discussion Locked

DVD-Drive Won't Recognize Movie DVDs

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a Memorex DVD+/-DLRWL1 F16 BSWE drive that is now lno longer recognizing any manufactured movie DVD I put in it. It will recognize datat CDs and burned DVDs, but nothing else. I run Windows XP.

15 replies

by pierrejamme

Just a thought.
Did you get any software with your DVD, for example I have Cyberlink PowerDVD that came with my Dell. If so, re-install and try again.

by hal 9000

That's odd! About the only thing that I can think of that would make this happen is something about the Region Code in the DVD Playing software preventing the DVD from being seen. You could try changing the Region settings in the Control Pannel and see if that cures the problem.

Other than that I'm at a bit of a loss to explain this behavior but I take it that you can only read DVD's that have been recorded in this Burner right? It would be interesting to try a recorded DVD movie to see if the Unit recognizes that one or just fails to see it at all.

Col

by hal 9000

Well since you can read rec ordered DVD's that where done on that Drive it appears that somehow the Tracking mechanism has come unstuck and it is unable to read Manufactured DVD's.

You could try cleaning it out with some form of compressed air as there may have been dust sucked into the unit which is limiting the Read Head from splitting the light properly so it is unable to track. This is a common thing if you live in a dusty place or the computer is sitting on carpet. It very much sounds as if the intensity of the Laser has somehow diminished and it is getting scattered too much by the Manufactured Disks but not by a Recorded DVD which has fewer layers between the outer surface and the data area of the DVD. But this should also apply to Manufactured CD's as well which you have said are working OK.

If the Drive is still Under Guarantee I would now be taking steps to return it to the agent where you brought it from or the Country/State Distributer and getting it replaced UG before the problem gets any worse. Of course if it is a tracking problem it is just possible that what you have recordered previously may not work.

Also can you return it to an earlier Firmware version? This may have some affect that makes it work properly.

Col

by dmiles

NOTE: Please adhere to the following guidelines while troubleshooting your DVD drive:

Always use a clean, scratch-free DVD disc when testing.
A DVD drive is significantly more sensitive to scratches and dirt on the disc than a CD-ROM drive.

Always be sure to test multiple DVD discs in each step.
This will ensure that the problem is not isolated to a particular disk.
If the problem only occurs with a particular disk, the disk is likely defective or incompatible with your drive.
To verify the basic function of your DVD drive, you may perform the following steps:

Close all running programs.
Insert a DVD disk into the DVD-ROM drive.
If the DVD begins to autorun, this is an indication that the drive is able to read the media. Close the DVD splash screen, if one appears.
Double-click the My Computer icon on your desktop.
Right-click on the drive letter for your DVD-ROM drive.
From the pop-up menu, click Explore.
A window should open displaying the directories on the DVD media.
Attempt to open (read) the various directories by double-clicking on them.
If you are able to read the DVD media using this method, it is very unlikely that the DVD drive is the cause of the DVD problem. The problem is probably software related (although, if you are using a hardware DVD decoder, this device may also be a possibility.) Typical steps for troubleshooting DVD include: verifying your display settings, cleaning out the Windows? startup environment, and reloading the DVD decoding or video adapter software. Search Support your Dell for more information on these topics. It may also be useful to search for software updates for your decoding software

by grumpus

I appreciate the quick responses but my problem's still ongoing. I've done the steps listed in dmiles' answer and still nothing. The drive will read a CD-ROM or a DVD burned on it just fine, but when I insert a movie DVD (and I've used about 6 to make sure it wasn't just one or two discs), the drive starts working for 4~5 seconds, then stops. The disc name never shows up in the My Computer window, and when I right-click EXPLORE on the drive, it says to enter a disc in the drive. I've uninstalled and reinstalled the drive, and used every firmware update I can find for it.

by ghimpe--

"...and used every firmware update I can find for it..."

I belive that's your problem. You might used a bad firmware... Please update the firmware with the latest version found on the manufacturers webpage!!

Also, does your problem ocour only when you try to read video-DVDs or does it also ocour when you read DATA-DVDs?? (ie: music, programs DVDs)

by grumpus

I'd actually only found one firmware update and it was from the Memorex site (it was BSWE) but I had already used that update a few months ago (and well before all this trouble started). The problem only occurs when I used video-DVDs. Every other kind of disc (CDs, data DVDs, video DVDs I've burned with that drive) works fine. But if I put a manufactured video-DVD in there, it won't recognize it at all.

by phonepkh

I have also had a problem with My memorex dvd multi format , the firmware is wrong on the website, also the instalation disc reads wrong and say's it cannot install, as it is a win32 problem, I am using XP and it see's the drive but just hangs and does nothing,I think it is a manufaturer defect, because I put back the old DvD player and it is all ok!
Now to re-run windows setup is not an option as my old disc is before XP service pack 2,
I checked the bios...it is seen....in windows device manager ...seen...I did note that it asked for the region for the DVD which I did! but no joy, I like Memorex have the external DVD burner,works great, but this DVD internal is a Pig, but I am on a mission to find a reason for it, I will give it another day then, Back to the Box and Back to the Store.

by ghimpe--

Well, it apears you have a Region Code problem. Do as Hal explained to corect your problem.

by sgt_shultz

not to be miss obvious but think drive has failed in some way. did you contact drive mfg for more testing ideas?

by acegolfr

It is not about drivers or firmware or any other than WinXp Sp2 has a built in disabling command for the CD/DVD burner if you try to burn any copywrite data Like making duplicate WinXP cds, still trying to find answers

by larrygfox

Was this problem ever resolved? I have two drives (older Hitachi GD-2500 DVD-ROM and NEC 3520-A). I've played dozens of DVD on the drives, and suddenly neither will recognize a pre-recorded DVD. CDs, CD-Rs, DVD-Rs, etc. all are fine -- it's only when playing prerecorded DVDs that the problem arises...

When inserted, the drive will either (NEC) spin up, blink, the spin down; or (Hitachi) spin up, light up, and continue to spin indefinitely while the hard drive light comes on. Windows Explorer never recognizes that a DVD has been inserted. Windows often has trouble shutting down successfully after this.

Changes to the system in the last couple of months have been: new hard drive (Seagate ST3120026A-RK 120GB), new video card (MSI FX5900XT with appropriate drivers), and the latest AGP & IDE drivers on the motherboard (ECS KT600-A w/AMD Sempron 2500+) to support the new video card.

I suspect that it's related to the OS -- I can't see both drives failing in exactly the same way at the same time, and losing *just* ability to read DVD-ROMs. But I can't isolate the problem...

by larrygfox

Quick update: On a hunch, I decided to simply uninstall the DVD drives in the Device Manager and reboot the system. After rebooting, the PC saw the "new" drives, configured them, then after another reboot, everything worked fine.

Things ran fine for a few days, then yesterday the drives again began failing to recognize a disk. I repeated the sequence above, and again they were fine.

*Something* is screwing up the drivers, but I can't figure out what...

This discussion is closed to new replies.