Discussion Locked

ECS K7VMA mobo AGP video vs onboard vid

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am using an ECS K7VMA motherboard that I previously installed using the S3 Savage onboard video card and driver in W98.
I would now like to use an Nvidia video card in the AGP slot provided on the motherboard. I can find no way to disable this onboard video in the BIOS or through the OS. All attempts to uninstall the S3 drivers and get the OS to recognize the AGP card have failed. Running the NVidia Detonator Driver installation results in an error message stating there was no NVidia card detected.
Does anyone have a solution for this? Would reinstalling W98 do the trick?
The ECS website offers no help on this particular issue, but in its forums I can see this is a common problem.

16 replies

by dmiles

Open the CMOS configuration panel and navigate to the Advanced tab,then look for the video listed,here you should be able to disable the onboard video

by putergurl

Did you mean the BIOS configuration that is accesed by pressing 'DEL' at start-up? Or is there another utility for this board?
In the BIOS/CMOS panel, there is no option to enable or disable the onboard video. Only the onboard audio and AMR seem to have this option.

by opatzg9

You could go into device manager and delete the video there and when windows redetects cancel out and then the default vga drivers will take effect.
Then try and get the nvidia to work. If you check uot the schematic for the motherboard is there ajumper to disable onboard graphics? Bios from hitting del is where I would have to think it would be located since you would need some video working before the agp card is fully installed by loading motherboard agp driver, diectx, nvidia driver, monitor driver in that order, and if the agp card should fail you should be able to switch the onboard back in bios before the agp card gets told to take control. Give it a second and third look around. Good Luck!

by thechas

Looking at the K7VMA manual, it looks like the option is in the integrated periphials section.

If they do not list the AGP slot, change it to the nearest PCI slot.

Then, the BIOS should default to your AGP card instead of the built in S3 chip.

Chas

by cg it

Well, I also took a peek at the K7VMA manual and as Chas said, the BIOS settings for the video appear in the intergrated peripherals section , "Init Display First". If as in other BIOS's , you can change the Initial Display First using the "page up"or "page down" key(s). This portion of the manual says [quote] "Use this item to define if your graphics adapter is installed in one of the PCI slots or select onboard if you have a graphics system intergrated on the mainboard" . Nothing else that Iread in the manual points to configuring the AGP vs onboard video.

by putergurl

Actually, this answer did help clarify the issue. Valhalla, as you state, there really is no option in the BIOS to select onboard vs AGP slot video. The only option is AGP vs PCI. Neither selection helps the board recognize the video card in the AGPslot.

by cg it

Well. hummm. Instead of the frustation of trying to figure out a board that seems to not want to use the AGP card no matter what, and if you really want to use your AGP vid card, dump the ECS and get one without the onboard vid. [note: On board video uses physical memory [takes away from system memory] to work. A negative in respect to running high end graphics programs such as games.] Chas uses Azus and Abit boards. I use MSI boards.

by cg it

Another thing you might want to try is flashing the BIOS. Check ECS's BIOS update page and see if a newer revision of the BIOS resolves the AGP port vs onboard Vid problem.

by cg it

If board prices are a negative in getting a new board, Newegg.com has "barebone" mainboards at a substantial savings. Barebones means no CD, No cables, no manual no retail box etc. You can get download all the drivers, chipsets and manual for the motherboard from the mfg site. Cables [80 pin IDE and floppy cables] can be purchased at any computer store. Its a good alternative to paying full retail price for a motherboard.

by cg it

I don't suggest Ebay as I've seen board prices on Ebay go for More! than one can get retail . I don't get that but then some people just love auctions.

by yelhsa3840

if theres no way in CMOS to dissable it check on the mainboard. sometimes theres a din switch or a jumper to dissable it...good luck windows wont matter trying to dissable it and you shouldnt try to delete the driver in fact most onboard components have drivers on the board itself

by putergurl

Good suggestions, everyone. I have since realized a major goof on my part that got the situation corrected. Your ideas are all good and I appreciate your input.

This discussion is closed to new replies.