Discussion Locked

Elpina - Motherboard

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I recently acquired 2 computer for free from a friend one has a fried mother board the other needs a "make over" so to speak. The one that I'm concerned with is the one that needs the "make over". I know very little about the computer because the person that I got it from knows nothing about computers except how to use them for the net. lol. But thats ok for him. I had trouble finding the maker of the mother board but it wasn't till I took everything off the board and looked on the back its made by "Elpina". I searched the net for their website and I never got the site to work. So then I went to some motherboard price comparision sites to see if they still sold them and I couldn't find it. My problem here is I need to figure out wheresome of the wires go for this motherboard so that I can get on my way. BTW I'm currently in my final year of high school so take it easy on me. I plan to go into the profession involving system administration so this is about the best way for a person to learn I suppose. Help me out if ya can, point me in some direction.

13 replies

by fred07

First some basics; Allways use a static wire untill you get used to keeping yourself static free. This can be done by touching the case at a metal point anywhere. When removing or istalling anything keep in touch with the metal of the case.
Cabling ide is allways red line on cable is pin 1 and you may need a magnifying glass to see the #1 on the motherboard.
Without a motherboard manual for that motherboard you are going to have a tough time of it. Hopefully answer 1 got you to a MB manual. If not go to your local pc repair shop and ask if they have a spare of any kind. This will give you the basic info and a few clues as to what you are into. You have only 2 ide slots on the MB and 1 floppy connecter. Primary ide is to Hard drive and secondary is for cd rom. This designation should be on the motherboard. Do not give up as either will work for hd. If you can, pull the cpu and send the numbers in comment and I or anyone here can tell you it's speed and maker. If the ram is present, leave it in the board for now.
I also need to know your power supply type. Leave it plugged in and tell me what type of connection it is. ATX is one double and an AT is two single.
Do not worry about the cdrom being in. Just the floppy and a hard drive. I just would like to see if it will boot before you get into it to far.
If this is a newer type than I think you will have a set of wires out of the case which have to be connected to the MB. If this is the case I will send thestart procedures in my next comment and or answer. Do have fun and do not be upset if this unit fails. I fried a few when I started.

by fred07

I was refering to the power to MB from Power Supply. Should be 2 at 1/4' wide by 1'long or 1 at 1/2" by 1". I am trying to figure out if you have an ATX or AT MB. After I know that I can better help you with the other connections. Your MB id would be in front ususally between the ISA or PCI slots. Although some are on the Boarder anywhere. A name may not be present, just a serial number or an ident number. Also I need to know what type of RAM it uses? Just a size of RAM would tell me what base type of MB it is. ie it's length would tell me a basic type. Either 5" or 4" or 3.5"????

by kinneym_98_98_98

I forgot so say that I know basics to networking meaning static guard, some power, and the IDE's, I dare not power it up incase some wires are in the wrong spot. thanx for the tips also shoulda clarified all that its my second year of networking but my class doesn't have much hands on right now. its still in the development.

The power supply has 2 plugs that can goto the power reciptical one plug is female and the other is a male plug. the power cord that I have works on the male recipltical.

by kinneym_98_98_98

I can say that the Spot Light website had a different MB than the one that I have. The computer that its in is a Tower, not a desktop. does anyone know of a website that helps to Identify the motherboard?

by kinneym_98_98_98

I was able to find the MB on the net, for ram it currently has 1 128mb PC133 and a 8Mx64 SDRAM PC100
since I found this it might be more help to me I will keep the question open incase anyone has any insite for me I check it 2 times a day usually morning, and after school

http://www.pcchips.com.tw/M571.html

Onboard 3D Sound Pro meet PC98 SPEC and support HRTF Positional Audio, Direct Sound, Software Wave-table Synthesizer
Support embedded 64-bit VGA chip
Support onboard L2 512KB cache
Support both ACPI and Legacy PMU
Support Ultra DMA/33 at maximum transfer rate of 33MB/s
TXpro-II BGA chipset/66MHz Advanced Graphics Port
ATX power support various functions, such as Suspend/Shutdown Switch and Alarm Wake Up and Modem Ring On
Support 64M-bit(16Mx4,8Mx8,4Mx16) technology DRAM/SDRAM

by fred07

Okay and here it is. Sounds like an ATX PS so just plug that in and go from there. The wires from the case and there should be several are fairly easy. Make sure they say things like PS or Power connect which can be two or three plug with only two wires to it. HD connect which goes to the HD connect on MB. MB will have in small letters the same type of initials. This is where a magnifying glass or I use magnifying glasses are important. Find the wires from the case to MB and tell me the initials on each and I will explain each as we go along and where they go on the MB. Okay. Did you find any type of ID on the front of the MB such as asi85963 v1 or al182795-v2.1 or any thing like that???

by fred07

Start with one RAM and let me know how the hookups are going. When you found the MB on the net did it give you a manual link? If so you are in great shape. It should show all power connectors and allow a MB drivers link. Did it give you these? fred

This discussion is closed to new replies.