Discussion Locked

floppy nightmare

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I now have two machines with floppy drives that do not work. One an HP on WIN98 and one a generic on NT 4.0. On both I replaced the drives with known good drives and they do not work. I replaced the cables. I removed the controllers and rebooted. The light is on but no disk activity....the HP just locks up. I'm open for suggestions.

17 replies

by dmiles

Check the drives to make sure you have not pushed the pins in on the back
Flip the cable over and try to insert on to connector to see if this works ,some drives Pin 1 is located on the opposite side
Check the motherboard to make sure IDE cable isseated properly.
Open the Device Manager and check for any exclamation marks at floppy controller and also at floppy drive,then make sure you have no conflicts with any other devices

by dirkfour4

did that....now I have another one on a separate machine with no attachment to or relationship with anyother machine...refusing to read floppy disk...or format one...have tried several. Don't think They like me

by mdelyea

If the light is remaining lit on your floppy it usually means the cable is backwards. Reverse the cable at the drive end. Also some floppies have pin numbers printed on the bottom. Make sure the red stripe on the cable corresponds to pin 1 on thefloppy.

by drdmc

Make sure that the cable end with the "twist" is connected to the floppy drive. As previously stated, make sure pin contacts are good and No. 1 is in proper position at both ends. With a multimeter, check voltages at your power connector. Put your ground lead on pin 2 and measure voltage at pin 1. Should be 12v. Now ground at pin 3 and measure voltage at pin 4. Should be 5v. If low or missing voltage, check power supply. If all checks out, possible cmos or controller (motherboard) problem.

by dirkfour4

instead I switched ribbon cables and switched drives (a total of three different ones) After booting, after windows is operating, I go to my computer access the A drive and wait....and wait. Then when it opens I get various messages depending on whether there is a new blank floppy in the drive or a known good data disk in the drive. For example: cannot access disk.... or CRC bad....

by dmiles

Check the CMOS panel and see if the BIOS is recognizing the floppy srive in the configuration panel,then try flipping the cable to see if this will work

by cvjack

Sounds like you need an exorcist. Check the floppy cables again, if the green light on the floppy drive turns on immediately after you power up the system(s) then the cable/cables are backwards. Also, have you tried reading/writing from many different floppy disks? They are totally unreliable and frequently go bad for no apparent reason.

by dirkfour4

if the green light on the floppy drive turns on immediately after you power up the system(s) then the cable/cables are backwards: NEGATIVE it does not.

Yes, various disks, blank or with known good data...and have tried three different drives now

by cvjack

Sounds like you need an exorcist. Check the floppy cables again, if the green light on the floppy drive turns on immediately after you power up the system(s) then the cable/cables are backwards. Also, have you tried reading/writing from many different floppy disks? They are totally unreliable and frequently go bad for no apparent reason.

by com_doc-19885035

Many motherboards will let you configure your floppy for multiple modes. Check in CMOS and verify that the setting matches the floppy. Selecting the wrong mode, or selectnig the wrong form factor (3.5" vs. 5.25") can also cause symptoms like you describe.

by dirkfour4

after considerable testing and questions and answers, the answer was "it's the power supply"!

by 1stladytech

Best to start to isolate the problem, will the machines boot to the floppy? Try bringing the Win9x machine up in DOS mode, (F8 at the start, choose Dos mode only), will it read the floppy then? Some viruses will give the activity that you are describing, if it will boot from it with no problem, but won't read from dos or windows, check for virus, especially boot sector.

Good luck

Vickie

by dirkfour4

after considerable testing and questions and answers, the answer was "it's the power supply"!

This discussion is closed to new replies.