3 replies
by ghimpe--
I assume you have an IDE hard drive. On your bobo you will have 2 IDE ports. Probably you have your hard drive connected to one of the ports with a 3 plug IDE cable. Your CD-ROM should be conected to to another IDE cable that plugs in the other IDE port on the mobo.
You can attach you second hard disk to whatever IDE cable you want (preferably though to pair it with the CD-Rom). All you need is to make sure you set the jumpers corectly. (the jumpers are small pieces of plastic with metal inside that shorts 2 pins. ) You will find information on how to set the jumpers on a label on sticked to the drive.
If you pair your second hard disk with the first one (both on the same IDE cable) make sure you set your first hard drive as master and your second drive as slave.
If you pair it to the CD-ROm (recomandated), set your CD-ROM as master and your hard drive as slave.
GooD LucK! ;)
by dmiles
Modern IDE drives can function in two modes: as the "Master" (boot drive), or the "Slave" (secondary drive)
lay the new drive in a stable position on top of the case (note to minitower owners, it's perfectly OK to do this with the system box laying on its side), using a book to create a flat surface if none is available. Power up the computer, enter CMOS setup, and either add the parameters for the new "D:" drive in the "Standard" menu, or use "Autodetect Hard Drive" to let the BIOS determine the parameters. Save the new settings, and let the system boot. If the system hangs, or reports an error, shut down, check your jumpers and cables, and try again. Windows '95 and NT users will go through the operating systems "New Hardware Setup" at this point, and can then use "Windows Explorer" or "File Manager" to copy the contents of the old drive to the new drive, unless they want to leave the new drive as the slave. If that's the case, Win '95 and NT users can shut the PC off, secure the hard drives at this point, put the cover on, and be finished. Otherwise, Windows '95 and NT users will also have to create an emergency boot disk, if you don't already have one, making sure that the "FDISK" utility is included on the disk, and can then skip the next two paragraphs.
Type "FDISK" at the "A:>" prompt, and choose option "2. Set active partition." FDISK will report that no partition is set active on fixed disk 1, and ask you if you want to make the partition active now. Confirm this, and DOS will report the partition is set active, and tell you to hit "Esc" to reboot the machine. Remove the floppy from drive A:, and hit "Esc". The PC will reboot and come up just like your old PC, except it will be faster, you will have more free disk space, and you will have a spare hard drive (D:) that you can use for data or backups. Turn the PC off and mount the drives into their bays, making sure to use at least three screws each, replace the cover and you're done.
by dmiles
Modern IDE drives can function in two modes: as the "Master" (boot drive), or the "Slave" (secondary drive)
lay the new drive in a stable position on top of the case (note to minitower owners, it's perfectly OK to do this with the system box laying on its side), using a book to create a flat surface if none is available. Power up the computer, enter CMOS setup, and either add the parameters for the new "D:" drive in the "Standard" menu, or use "Autodetect Hard Drive" to let the BIOS determine the parameters. Save the new settings, and let the system boot. If the system hangs, or reports an error, shut down, check your jumpers and cables, and try again. Windows '95 and NT users will go through the operating systems "New Hardware Setup" at this point, and can then use "Windows Explorer" or "File Manager" to copy the contents of the old drive to the new drive, unless they want to leave the new drive as the slave. If that's the case, Win '95 and NT users can shut the PC off, secure the hard drives at this point, put the cover on, and be finished. Otherwise, Windows '95 and NT users will also have to create an emergency boot disk, if you don't already have one, making sure that the "FDISK" utility is included on the disk, and can then skip the next two paragraphs.
Type "FDISK" at the "A:>" prompt, and choose option "2. Set active partition." FDISK will report that no partition is set active on fixed disk 1, and ask you if you want to make the partition active now. Confirm this, and DOS will report the partition is set active, and tell you to hit "Esc" to reboot the machine. Remove the floppy from drive A:, and hit "Esc". The PC will reboot and come up just like your old PC, except it will be faster, you will have more free disk space, and you will have a spare hard drive (D:) that you can use for data or backups. Turn the PC off and mount the drives into their bays, making sure to use at least three screws each, replace the cover and you're done.
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending