Discussion Locked

Hard Disk Optizing

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a 10gb hard disk with one partation in a Windows 98 SE computer. Recently I am getting messages that I have run out of capacity. The useable space seems to be only 3.2gb instead of the full 10gb. How can I utilize the full 10 gb on this hard disk?
Is there a comatability problem in Win98SE that limits the size of hard disks that can be used?

12 replies

by thechas

Windows 98 does have some hard drive limits, but thay come into play at 32GB, 64GB, 80GB and 137GB.

3.2GB is a new one on me.

There are numerous size limits that affect many older motherboards.

One very common limit is 8.4GB.

Is the 3.2GB the free space, or total drive capacity?

Double click on the My Computer icon, then right click on your C: drive.
Select properties.
You should see a pie chart showing you used, free and total drive capacity.

If it shows the total drive capacity as 3.2GB, then I need some more information about your computer before I can give you a detailed answer.

Make and model of both the drive and the computer, or the make and model of the motherboard in the computer.

What I suspect happened is 1 of 2 things:
1. Your motherboard only supports drives up to 3.2 GB. When the drive was installed, it was not noticed that there was a problem.

2. Someone accidentily set the Primary DOS partition on the drive to 3.2 GB instead of using the entire drive.

The fix for option 2 is easier than the fix for option 1.

You can also watch the monitor while the PC is booting up.
It should flash the drive capacity as recognized by the BIOS shortly after the memory test.

As I said, the options for what to do depend on your hardware and it's limitations.

One last question, are you willing to format the hard drive and re-install Windows in order to correct this problem?

Chas

by maxwell edison

W98 should install and operate just fine on a 10GB drive/partition - and be able to utilize all of it.

It could be that you have a 10 GB hard drive, but perhaps with only one partition - a 3.2 GB partition. When initially installing W98, the partition size can be selected. Perhaps the person who installed it only created a 3.2 GB partition.

You could run fdisk to check the partition(s) and the sizes allocated. Or a utility like partition magic could help in that regard.

by chedester

On My Computer I have the following:
Used Space 3.75GB
Free Space 180MB
Capacity 3.92GB
The computer has been converted to FAT32.
Mother Board: Gigabyte p-11 GA686LX
Hard Disk: Maxtor N256 10GB
M/N: 90121U2
P/N: 168096-01
Installed 12-2-2001 by third party.
Relunctant to format HD but if that is the only way need instruction to keep programs and files. Only have old zip drive for backup.

Thanks for help.

by twitchmyth

I think Maxwell has the right idea here...its more likely to be incorrect partitioning. Use Fdisk to check - boot to floppy and find out.

It could be simple unpartitioned space, or it could be a WinNT/Linux partition, as these wont be detected by9x.

To repartition, you CAN use fdisk, but it's data destructive. Much better option would be something like partition magic as it is a non destructive partition creation and resize utility - of course if you are changing FS's from NTFS to FAT32it's destructive (although not vice versa thanks to convert)

by chedester

Re-Format HDD and installed Win XP Professional.

Never found why HDD was partitioned at 3.2GB. Too much time in attempt to correct problem.

Back-up all data and restored after inatalling Win XP.

Everything OK now.

Thanks

by thechas

So, you did re-partition the drive and installed a newer version of Windows.

You left the question open.

Do you need further assistance?

Chas

This discussion is closed to new replies.