Discussion Locked

Hard drive problem

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

I have a Pentium II,333MHZ and am trying to install a 40GB hard drive. It gets detected as slave no problem but when I set the jumper to master it doesn't get detected as master. On boot up I get a message saying there is no primary master. The system knows it's there and recognizes the full 40 GB but not as master. It's A Maxtor drive and I used their program to install it. Any help is appreciated.

11 replies

by tamj123

When you change 40gb hard drive to master, is there other IDE device connect on same cable? if does, then you have to set the jumper to master w/ slave, otherwise, set the jumper as single master only.

by sgt_shultz

is it a Master or is it a sole drive? i didn't think maxtor's cared but just saying...
you sure you have proper setup? slave drive installed, jumpered correctly, known to work?
tried another cable? tried examining relevant BIOS settings? maybe you need to force drive detection?

by smith2994

Poster rated this answer.
Tried it all and everything is as it should be as far as I know.

by tabcomputers2002

I had the same problem on a Maxtor drive, BIOS properly detected it, but it wouldn't work right. As it turned out, the new drive was ultra ATA, but my board accepted ATA.
I got around it by using the cable that came with the board and not the one that came with the drive.

Hope this helps.
Tim

by gigelul

"I used their program to install it"
How did you used it? Generaly you must boot the PC with their boot diskette only when BIOS can't detect all the parameters of the HDD.
You tried with the fdisk? No primary master?

by thechas

If you used Maxtor's install disk, you may have setup a drive / BIOS overlay utility. These are commonly used to allow older motherboards to access hard drives that are larger than the BIOS can recognize.

The utility installs to the boot sector of the Master drive.

First, switch back to your previous configuration and back up ALL critical data.

Then, set the 40GB drive as single master and boot up from the Maxtor disk.
What you want to do, is either recover the drive, or remove the drive overlay program.

The Maxtor software should allow you to set up the drive as partitioned with the data intact as the Master drive on your system.

Chas

by boli

Have you tried BIOS update? that might fix it.
your not running windows 95 are you? i spose it doesnt matter if the comp wont see Hard drive as master...
try and see if the computer see's it as a master on a different channel, see if its the other channel or the drive jumper's are broke.

by otl

Used Maxtor supplied disk to install, their large disk support is on what was your primary HD, and is telling the computer that what you want as your primary HD is the secondary thus no master.

Did you Fdisk it (by itself) ? and create a primary DOS partition. Or Fdisk while it was the secondary drive, creating an extended partition ? Fdisk (on Win 98 and above boot disk) allow an overlay program for large disk support, written to the HD information.

To remove their overlay program put the PC in the same configuration as when you installed their program, follow the instructions in the book that came with it.

1. Set up HD as single master, boot with windows emergency boot disk.
2. At A:\ type FDISK
3. Leave it "Y" at enable large disk support.
4. Set up a primary DOS partition of whatever size you want (default is the entire disk).
5. Exit Fdisk, reboot, format C:\ /S (/S makes HD bootable)
6. Remove floppy and type c:, at c:\ should be able to do a dir and see if the whole disk is there.
7. Change it back to slave to copy system files or reboot with the System CD in the machine to get a fresh software installation.

BTW - Do not care for OEM supplied program to install a new HD, get very strange results while trying to use them, unless used on all HD's.

by jesuss

Pentium 2 compatible motherboards do not recognize HDDs beyond 15 GB for Master unless you have the appropriate controller card installed. It can be used as a slave drive for storage. The cable is pretty much irrelevant without the actual UATA controller.

This discussion is closed to new replies.