Discussion Locked

hard drive problem !

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,

I am trying to install windows9x on a PC. When I boot it up, the system says "Primary Disk 1, disk 0 etc could not be found".

I have checked the connection of the HD to the motherboard and it looks firmly connected.

The BIOS was set to AUTO on the Types of hard drive.

Then I tried to boot up from Floppy disk and when it was started up from A: drive, I just couldn't change the drive letter to C: (which is what I thought would have happen)

I have checked the jumper setting and it is on master (which is correct as there is only 1 HD).

Could it be a dead HD or something else that I have overlooked.

Please help
Ed

11 replies

by still_learning

Hi, Recheck your connections at the drive and on the motherboard. Also ensure that the red edge of the cable is connected to pin 1 (or the red edge is closest to the red wire of the power connection. Make sure that the drive is jumpered for Master, if you have a CDRom drive make sure that is is jumpered to Slave or Master on the second channel. Make sure that your drive powers up when your turn your system on and BIOS detects your hard drive. If none of this works or if your drive makes any unusual sounds, your drive may have failed. If you have another drive, you may want to install Windows on it and then see if you can access this drive as a Slave. Hope this helps.

by thechas

Am I correct that this is a new or refurbished hard drive?

You need to run fdisk to partition the drive before you can access it.

Then, you need to format the drive before you can install Windows.

For W95, you need a 'startup' disk. The boot disk that you can make from inside W95 does NOT include the CD-ROM drivers and other needed files.

Links to help you out.

www.fdisk.com/fdisk
www.bootdisk.com
www.aumha.org

Chas

by fenaikh

Hi

1. article

Troubleshoot hard drive failures in seven easy steps
https://www.techrepublic.com/article.jhtml?id=r00320011217fai01.htm

2. article
200 ways to revive a hard drive

https://www.techrepublic.com/article.jhtml?id=r00320010115jed01.htm

3. Download
200 ways to revive a hard drive
https://www.techrepublic.com/download_item.jhtml?id=dr00320000510jed01.htm

4. FREE Data Emergency Guides

a. Original Guide
(300KB PDF file)

b. IT Professional Edition (411KB PDF file)

http://www.actionfront.com/af501red.asp

warrning:
they may have the same file name so download them with a diffrent name or location.

5.software Damage

software trial will only show files. license software will recover.

EasyRecovery 6 (repair & recover)

http://www.ontrack.com/easyrecovery/

6. Physical Failures and Logical Damage
http://www.actionfront.com/drives.asp

7. Recovering Data From a Bad Hard Drive
http://www.overclockers.com/tips1044/

8.Hard Drive Mechanic GOLD Features
http://www.highergroundsoftware.com/features.htm

Good luck

Mohamed

Note1:
***Very Important NOTE *********
After you copy the URL a space or a %20 maybe gets inserted in the URL when you paste it into your browser. Delete any spaces or such characters from the URL for the page to be loaded.
***Very Important NOTE *********

by cg it

I think Chas has it right. You have to format the drive, then make a primary partition [which will be C:] before you can change drives from A: to C: ..further, to install an O/S on the C: drive [partition] you have to make it an active and bootable partition [all of which fdisk will ask you when you first create the primary partition.

by martin.hoer

Before going to a lot of trouble check to be sure you have the drive plugged into the last connection on the ribbon cable,(yes it can make a difference) even if it is the only drive. If it does not boot then I would try second or middle connection.Only then would I go on to the other reco's.

Martin

This discussion is closed to new replies.