Discussion Locked

Hard Drive Problem!!

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Hello all the other day I decide to back up my pc to another pc hard drive that had ntfs partion (maxtor 60gb) I move about 45gb of data onto that drive to a folder on the root all the data moved over fine and I got to reload my system but after I got windows and everything installed I called it quits for the evening (bad move) so I shut down the pc that had all the data on it the next day or so I tried to power it up with no luck so I took the drive out of the pc and made it a slave to my other system the bios could see the drive and device manager could also but no luck in disk management I think the partion has gotten crupt or the drive has just crashed any suggestion I had a software package that worked before in the past for something like this but it was backup on that drive any suggestions??

8 replies

by dmiles

Here's what may be causing the problem:

1. Make sure you configured the target disk as
a basic disk (as opposed to dynamic disk).

2. Usually, if you can't make the target volume boot
from the floppy disk you made, there is something
wrong with the target. But, in most cases, it is
as simple as not having the right entries in the
BOOT.INI file.

3 So, I urge you to check the contents of the BOOT.INI
file. The floppy-based boot sequence is more forgiving
than any other method.

Since the most troubling aspects of the system boot
sequence are all taken care of by the floppy disk,
as long as the contents of the \WINDOWS\ directory
and the system registry files are present in the
target volume, it should be OK.

4. There are other cases where the boot sequence fails:
e.g., when the volume for which the virtual memory
is allocated is not on the same volume (typically C:)
and the volume is not accessible at the boot time for
any reason, the system fails to boot

by hal 9000

Well firstly I would put the drive back where it came from and try a floppy boot disk to see if the partition remains.

The obvious thing is that the MBR's have become corrupted or maybe even you have used so much HDD space that the page file can not initialize. As you didn't post the version of Windows that you are using on the backup computer it is a bit hard to give you any more details than what have already been given. However the most likely reason that you can not access the drive in the other computer is that it is set to the primary partition and you can not have two primary partitions on any Windows box.

But you should at least be able to get it to boot in some fashion from the boot floppy. Failing that it is time to drag out whatever Data Recovery utilities you have available and recover the data off the drive. This is a very time consuming and tedious task that shouldn't be necessary if you backed it up correctly and checked before you stripped your existing OS out and reloaded or even backed up to several CD/DVD's and checked them before you started removing anything first.

If you do not have any data recovery tools while On Track is the best available it is also very expensive to purchase so for a cheaper alternative X-Ways Davaro is a good choice as it is under 40 euros and a lot cheaper than the On Track option but no where near as fast. you can find a trial download at

http://www.x-ways.net/davory/index-m.html

This trial version will only pickup the first 200 K of any one file but it will show what is possible to recover before you pay for it.

The other option is to try Iolo's System Mechanic5 not the Pro version which can be downloaded as a 30 day fully functioning trial version at

http://www.iolo.com/sm/download.cfm

by hal 9000

But be extremely careful with this as if not used properly can do more harm than good but it just may be possible to rebuild the corrupted MBR's with it but as a general rule of thumb if it prompts you with a message that it is about to make changes that will not be reversible DO NOT perform this task! Iolo also has a Search and Recover program but as I've never actually used it I'm unsure just how well it works but it is available at the same URL and I don't know what the trial license actually is.

Remember with any Data Recovery program only scan the damaged drive for data and always save it to another HDD or other media never to the drive that it is coming off as it will over write the other data that is on the drive and make it unrecoverable.

Lets know how you get on

Col

This discussion is closed to new replies.