Question Locked

Hard Drive seen in bios, but not when booted up?

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a problem with a stand alone computer which runs on Win98se, two drives were fitted one for OS the other for data (as slave). I can no longer access the slave drive data for soem reason, drive spins up and is seen in bios, but does have some garbled letters etc after name now? However once computer has booted only C drive can be seen? D drive not visable in My Computer? Have tried starting with a floppy startup disk as was told MBR may be damaged or lost? With command fdisk/status or fdisk/mbr get message drive not found?

Can anyone help please as not all data had been backed up as someone had messed with back up program!! Need to access data or im in the **** as it were.

Please help

Kev

7 replies

by hal 9000

So there are no MBR but FAT Tables that need fixing.

Best guess is make sure that the drive is still plugged in properly and that the IDE Cable hasn't become partly removed then try again. Honestly because of your description it sounds like the IDE Controller is dieing so you just might get away with trying it on the other IDE Chanel or in a USB Caddy and plugged into a USB Port with the necessary drivers installed.

If you can not repair the FAT you'll need some form of Data Recovery Program and here you pay for what you get the best is On Tracks Easy Recovery Pro here

http://tinyurl.com/y4bwd7

Then you need different programs depending on your ability and knowledge with Hex so if you know Hex Inside Out you can use this as a recovery tool

http://tinyurl.com/8bd3f

If you don't know the first thing about Hex this will do far more damage than anything else is capable of doing and as a result cost you far more to recover the data.

So if you want an Nontechnical Data Recovery program to use here is a list of available ones. I haven't used them all or even most of them so I'm unsure of just how well that they work and remember that any time you recover data you need to write it to a different drive to prevent overwriting the files and making it impossible to recover other data that you've over written.

http://tinyurl.com/afu2j

http://tinyurl.com/pfuhz

http://tinyurl.com/rmvrv

http://tinyurl.com/nc4kx

http://tinyurl.com/70lc

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

But if the data is ultra important you are better off giving it to a Data Recovery House to recover the data off the drive as they will not muck it up and work fairly quickly.

Col

by hal 9000

Fix FAT to bring the 2 copies of the File Allocation Tables back into agreement with each other and the MBR Fix was mainly used on the NTFS Partition.

God DOS commands are so much messy particularly when it comes to M$ DOS. :(

But anyway as the Fix MBR has been run without success that doesn't seem to be the answer here does it?

Col ]:)

by dawgit

Just how much data was on the Hard Drive just before it disapeared? Was the drive full? (remember M$ has limits on capcity on drives, after something like 95% full, bye-bye drive. the Drive will revert to FAT) -d

by 1bn0

Yes. The "backup" copy of the fat was usually used to "fix" the first one if it got corrupted.

But DOS doesn't do NTFS, still has an MBR.

Unfortunately, I don't think there is any answer to fix this problem.

Every time I have run in to this condition, it usually indiactes the FAT(s) and the MBR are just worn away to the point where they will no longer hold data.

Sometimes you can get SOME data of the drive before it fails completely. The more you play with it the worse it gets and the faster it degrades. Not much more you can do.

He says they've been running Win98. I take that to mean they've been running it for a quite a while. The drives are OLD.

The 3 things you can count on in life:
Death, Taxes and Hard Drive Failure!

by ghostbrowser

The garbled letters means the data transfers to and from the drive are bad
So any changes to the data may be corrupted
Try slowing down transfers by useing pio4
That is disable Ultra DMA (UDMA) or ATA 33,66,100,133
This may stop the garbled letters
If then you can try to copy your files off the drive its slow but may work
But you need to get rid of the garbled letters

Good Luck

This discussion is closed to new replies.