Discussion Locked

Harddisk Conflick Part2 (Weired) !!

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Remember i have harddisk conflick when i install second harddisk on my computer, is about the drive letter, titled 'harddisk conflick' but i have close the topic when i thought it's ok. 'TheChas' have help me by installing the sofware called 'LetterAssigner'. Actually is ok after i install the software, but later not long then my pc can't detect my second hdd, sometimes i restart my pc then can detect and sometimes don't. Things getting worse and my second hdd don't even detect at all everytime i on my pc and even i restart my pc, i uninstall the 'Letter Assigner' but still can't detect my second hdd. I have tried plug in and out to make sure one more time but still can't detect. If i enable my second hdd and disable my primary hdd then it can detect. I have set my jumper correctly. Pls help me on this weird stuff. 10q!

6 replies

by oz_media

Soorry, I missed the first question you posted, forgive me if this is stuff you've tried already.

"If i enable my second hdd and disable my primary hdd then it can detect." Have you tried reversing the Slave/Master settings? i.e Drive A was master, now make it slave and drive B master.
Have you tried using separate ribbon cables to the mother board? Sometimes having you CDROM and HD on one cable and the second HD on it's own cable (as master) will work.

by oz_media

You said you roperating system was built by Microsoft, that should be enough of an explanation itself.

Sorry, like I said, I didn't see the first thread so I can only offer starter info.

by cute_d

but why the first few days can work then after that can't work already. very odd, i did't change anything at all.

by thechas

Forgive me for forgetting the details of your original question. I look at and answer many questions every day.

Since I recommended Letter Assigner, I believe that you wanted to keep either your old drive letter assignment for the CD drive, or a logical drive on the master hard drive.

Now, my first suspicion is that you have a program installed that uses a Digital Rights Management system that writes a code to the restricted sectors of the hard drive.

This is the same area of the drivethat Letter Assigner must use to allow you to work around the default DOS drive letter assignments.

Or, you have picked up a virus that writes to the Master Boot Record.

Start by updating your Anti-virus software and running a virus scan.

If that does not find anything, you need to clear the Master Boot Record on BOTH hard drives.

CAUTION: DO NOT USE THE FDISK /MBR COMMAND IF EITHER DRIVE WAS SETUP USING A DRIVE OR BIOS OVERLAY PROGRAM!!!!

Boot from a startup floppy for your version of Windows.
At the DOS prompt, run the command
fdisk /mbr

Then, use the command:

fdisk /cmbr 1

(/CMBR - Recreate Master Boot Record on specified disk
Works as /MBR with the exception that you specify the disk to have it's MBR recreated. FDISK /CMBR )

You should now be able to boot up and see the drives with their default DOS drive letter assignments.

Since I do not know what software you have, I don't know if you have a DRM issue.
If so, you likely cannot use LetterAssigner to change your drive letters.

Let me know if I can be of further assistance.

Chas

by deadly ernest

If your problem is NOT with the MBR it may well be a drive hierachy conflict with the HDDs. This is rare nowdays but I used to see it a lot during the Jurassic period. If this is your problem the only way around it is to place the hard drives on seperate IDE channels, set one up as the Primary Master and the other as the Secondary Master.

The conflict comes about due to them both sending information to the IDE controller on at channel and the IDE controller gets confused as they both claim the same priority rights. Moving them to different channels resolves that issue.

by cute_d

Chas, i have tried to do your steps but still can't be done, any more good easy idea?

This discussion is closed to new replies.