Question Locked

Help installing SATA Samsung DVD

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi all,
I am trying to install a sata Samsung DVD-RW drive to my system.
The system is using a Gigabyte GA-945P-S3 motherboard with Intel Core 2 Duo processor running Win XP SP3.
The m/board has 1 x IDE connector, 4 x SATA connector.
Currently I have the following attached.
1 x IDE 150Gb hard disk & 1 x LG DVD-RW (both on the same cable)
1 x SATA 250Gb hard drive
1 x SATA 500 Gb hard drive.

If I attach the new Samsung DVD the machine will start its CMOS run, but then stop part way through and just hang.

The manual seems to indicate that this DVD should be OK to connect, but it's not happening.

Any help appreciated.

Thanks
Craig

12 replies

by balge

hi
could try checking the BIOS settings, make sure its not trying to boot off your new drive or the PSU may be struggling under the load? What power supply do you have?
cheers

by robo_dev

Also, make sure the DVD drive is getting power....does it sound like it is initializing? Does the tray open/close when you press the button?

Try swapping PSU connectors between the SATA DVD and HDD. If the HDD no longer works.....

As balge noted, your PSU could be overwhelmed.

Is the DVD drive visible to the BIOS of the PC if you go into the BIOS setup screen?

by pastorcraig

Thanks for your reply.
Yes, DVD initialises OK and is detected during boot screen.

It seems that if I remove one hard drive (not C:), then plug DVD into that slot it works fine.
I have tried every combination and it seems I can only get
1 x IDE & 2 x Sata connections to work.
If I connect the 3rd sata drive (DVD or hard drive) it will not boot beyond BIOS start screen.
However, there are 4 sata connectors.

Any ideas?

Thanks
Craig

by pastorcraig

Thanks for your reply.
Yes, have checked BIOS and is definately booting from hard drive.
Power supply is the standard one that came from the computer shop. 420w I think.

by robo_dev

By default some PCs, such as Dell, do not have all the SATA ports enabled in the BIOS setup. This is most likely not your issue, but something to look at.

There may be some advanced BIOS settings on your PC that are important...not sure.

I would reset the BIOS to factory defaults, as sometimes things get messed up.

Also, inspect all connectors/cables closely, and swap out the cables for differnt ones, it could be a bad cable or connector on a device.

Look for a BIOS update for your PC motherboard. It is possible that there is a bug in the bios version you have.

by pastorcraig

Hi,
Thanks for your recent help.
I have worked around it by installing a new/additional PCI SATA card. Problem solved.
Many thanks
Craig

by balge

hi
have you tested
all drives work
all cables work
all ports work
all detect in BIOS

if they all work separately but not when they are plugged in together, at the same time, then I don't see what else it can except PSU not being up to driving all six drives?
What exactly happens when "it will not boot beyond BIOS start screen"
cheers

by pastorcraig

Yes, all drives work OK.
Yes, all cables work OK.
Re ports, how do I test them? If a drive works on one sata port, will it work on all 4 sata ports on the m/bard?
If I plug a working drive into sata port 4 instead of 1 should it boot up the same as normal?
Yes, all ports detected in BIOS.
I have 1 x IDE cable plugged in (with a x DVD & 1 x 150Gb drive attached)
Also, 2 x sata hard drives on individual sata ports.
If I try to plug in another sata device the boot screen gets part way through then freezes.
I can send a screen shot, but not sure how.
Thanks

by balge

hi
not bothered which ports you boot from just to be sure that all the SATA ports actually work with a drive plugged in, be it HDD or optical.
Are you booting off the IDE ports normally?
Just a description of what's on screen when it hangs would do
cheers

by pastorcraig

OK, I have found the problem. Hidden deep in BIOS options is a switch for sata ports.
Options are normal, combined, enhanced + a couple of others.
However, they are all blanked out (cannot be changed) It is set on normal with sata ports 3 & 4 disabled. There is no way to enable them.
I guess I'm just stuck with 2 operative sata ports & 2 inoperative ones.
I have tried every combination & setting to do with sata control, ibcluding "load optimum settings" & "load failsafe settings". All to no avail. The options remain blanked out.
Thanks for your help.
Craig

by balge

hi
hmm well you could check Gigabyte for an updated BIOS and flash it, if available or check their support.
Otherwise, you could fit a PCI SATA card to utilise your new drive?
cheers

This discussion is closed to new replies.