13 replies
by pauline666 Accepted solution
by older mycroft Accepted solution
This suggests that you [u]removed[/u] the fan assembly and since fans are attached to their heatsinks, you must have removed that as well.
This alone will have broken the seal of the thermal paste between the heatsink and the cpu - this will require cleaning off (of both surfaces) and renewing.
Perhaps if you could expand on the details of "[i]now i have problems..[/i]" we might be able to help further. ;)
by pauline666 Accepted solution
by 1bn0 Accepted solution
As Mycroft said the fan is usually attached to the heat sink. SOmwtimes pulling the fand and heatsink assembly will also pull the cpu as the cpu is "glued" to the heat sink by the thermal paste.
If the cpu came out you can't just push it back down. (unless its a P1 or older processor) You need to release the tension bar on the ZIF socket before re-inserting the cpu. You also need to replace the thermal paste with new.
by older mycroft Accepted solution
Jeez, it's aeons since I've seen that happen.
But happen it does.
Good catch. :)
by pauline666 Accepted solution
You will laugh at this, I was almost in tears. Yes the cpu did come out when i took the fan out to clean it and i did not know it was the cpu neither lol, when i replaced the fan i just slotted it back in and put clips back on.
Proceeded to start up pc and it wouldnt load up, after further investigations we then discovered I had bent several pins on the cpu, so I know that the cpu is knackered but now I dont know how to check if the motherboard has been damaged any suggestions would be gratefully recieved.
Thank you
by maxpowers410 Accepted solution
HP use beep codes to identifiy problem specifically, which (sometimes) help. What kind of motherboard you got? Try look up on google "(Motherboard Name) +beep codes" or "error codes"
:)
by 1bn0 Accepted solution
I have straightened bent pins on a cpu before. But you had better be SLOW and CAREFULL. If you break a pin your done.
If you can successfully straighten the pins. I would try re-inserting the cpu in the motherboard, PROPERLY :) and give it a try. I would not attempt to use another processor as the board MAY have been dammaged by what has happend already. I also would not attempt to use the CPU in another Motherboard.
If you can't get the cpu back in order I would write off both the motherboard and cpu.
by ---tk--- Accepted solution
Bent pins... been there... like other posts have said be careful!! I had a friend with an old AMD sempron.... bent pins, needless to say we attempted to streighten them, one broke off... theres a CPU down the drain... Yes we still put it back in the board, lol, it wouldnt POST... o well.. live and learn...
Another friends issue: he was "cleaning" the system, wanted to remove the CPU fan, not knowing that it attaches to the heat sync, heat sync attaches to the socket... socket attaches to the motherboard... I still wonder how hard he actually had to yank on it to pull the entire socket out of the board...?
If you streighten the pins enough for it to slip into place, apply thermal greese, it still might work... Best of luck!!
by pauline666 Accepted solution
by ---tk--- Accepted solution
Are all the bent pins still attached to the CPU? if not did they fall off when you tried to bend them back?
If the pins are still in the socket, then your kinda SOL, you could try shakeing them out... or take some tweasers and magnifying glass and try to pull them out, with the latch unlocked...
Or if your positive none of the pins are still in the socket you could purchase another CPU, and give that a shot (dont forget the artic silver thermal compound).
What is the model of the PC you removed the CPU from? If its old it might be cheaper to just get a new PC... or if you can find one used on Ebay...
by pauline666 Accepted solution
by rob miners Accepted solution
Belarc Advisor. It may tell you the Motherboard Model but I wouldn't be surprised if it's proprietary. It should be listed under Main Circuit Board.
http://www.belarc.com/free_download.html
Median contacts.
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending