Discussion Locked

How do read a Non-Dos Hard drive

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

One of my co-workers had a secondary hard drive which he stored some files he was using on a windows 95 old packerd bell computer. The hard drive was working find as a storage media at that time. He removed the hard drive to install it into another computer to retrieve the files. The new computer runs windows 98 SE. The Bios recognizes the drive perfectly, but when the computer boots Windows 98, the drive even though recognized in the device menu, is unable to be accessed.

I then went into Fdisk to see how the drive was partioned and found out that it is of type NON-DOS and is not FAT16 or FAT32. That is under the "system" in Fdisk it is Blank.

Do you have any information which might help us retrieve the information on the hard drive?

Please Advise....

11 replies

by opatzg9

It sounds like the drive has drive mastering software running it, western digital, seagate and the rest used that for larger drives when bios would not recognize the drive. Best bet is to put it back in the packard bell back up what you want, transfer it, fdisk it with the /mbr option and format it. Good Luck!

by sdantzscher

The drive is a Conner drive which is now supported by Seagate. It is only a 1.2G drive, The old Packard bell computer was hit by lightning and consumed at which time the Conner drive was NOT in the computer. The problem is there are important files on the hard drive, unfortunately which my co-worker did not back up....The BIOS immediately reads the drive on the computer and it can even be viewed in the WIN98 Devices, but it has NO drive letter assigned and is not readible by windows or DOS...Thanks for the try...

by thechas

I have to agree with opatzg, some form of drive overlay software was installed on the old PB system.

It likely was so that a larger hard drive could be used as the primary master drive.

Most of these drive overlay software packages make it difficult to not use them on all drives.

What I would start with, is to try and identify what the master drive was on the PB PC.
Then, set up a system with that mfgs drive as the master, and run their drive overlay software.

You can also see if OnTrack www.ontrack.com or SpinRite software can help you out.

Chas

by opatzg9

Ok, so lightning fragged the PB. You can take that as a sign from GOD and a lesson well learned. Another thought is to get a hold of someone elses older win95 class machine and see if it reads the drive the same. newer machines are goingto detectit in bios and yes they won't let you read the drive with the overlay that was applied. I don't suppose he has the diskette which did the overlaying. My first machine was a 286 which I upgraded throu 386,386, new drives, p133, p233 and yes I used the overlay software in the 486 and 133 to use the drive which was a 1.6 gigWD. I don't know if you can read the drive without going back to the older controller and older bios setup. Good luck! You might want to check out local pc user groups or the tech department where you or your friend work if they have some old relics around which may be able to read it. I'd have to think you'ld have to find someones old basement computer for the kids machine since most businesses upgrade every 3-5 years and especially for the year 2000 so you're kind of out of luck there unless they like paying for storage. I know I have a couple old motherboards laying around, specifically the 486 and the amdp133. Part of my home museum(to allow me to not have to keep telling my wife why they're downstairs on the shelf). I'ld have to think there's others like me out there even in your neighborhood with the same deal going. Good Luck!

by bagmaster50

Just a word of caution. I've had to use drive overlay before to fool an older 486 bios to use a WD 1.5 gig. when I removed it and tried to use it in another machine, I had to remove the overlay software before the OS would read it. In the process ofremoving the overlay it also lost all the data on the drive. I had 1 very unhappy customer to deal with on that one. So, now I don't fix old 486's that require overlay software in order to use a drive. I'd rather install an ide controller card.

by wlbowers

One Possibility
Did he compress the drive. If so a file resides on the original c: drive that holds the key.

Lee

by wlbowers

Are you sure the drive was not compressed. Microsoft used this for more space because effectively it is one big file. The magic read file is stored on the boot drive.

This might not be the case but is worth considering.

Good Luck Lee

This discussion is closed to new replies.