Discussion Locked

How to create an MS DOS boot partition

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi.
I'm trying to install Windows 98 on a 2nd fixed disk that I installed in my Windows XP computer (seperate hard drive using NTFS). I have partitioned the 20GB drive into 2 10GB partitions with FAT32 and formatted the drive. (Note: After Win 98is installed I want to install Windows 2000 Prof. on the 2nd 10GB partition.) When I try it install Win 98 to the 2nd fixed disk, partition 1, I get this error, "Message SU0013. Setup cannot create files on your startup drive and cannot setup Win 98. If you have HPFS or NTFS you must create an MS-DOS boot partition. See setup.txt on the setup disk 1 or the Win98 CD. (I looked at the setup.txt file and it didn't help me.) I have looked for answers on how to create an MS-Dos boot partition but can't find an answer. Can you please help?

Thank you.
Laura

8 replies

by thechas

Windows 98 doesn't know about XP or W2K, and assumes it is the newest operating system, and needs to install the boot files (command.com, autoexec.bat, etc) to the root of the active hard drive.

The best thing to do, would be to start over from scratch.

Install W98 on the C drive.
Then, W2K on the D drive.
Finish with XP of the F drive.

That said, here is something you can try;

If you have a spare hard drive, temporarily replace your C (XP) drive with it.
Install 98 on the D drive.
Copy the files in the root folder over to the root of the D drive.
Then install W2K to the E drive.
Print out the boot.ini file that W2K creates on the C drive. Copy the file onto either other drive.
Also copy the files from the root of the Cdrive over to the W2K drive.

When you replace the C drive with the XP drive, you will need to manually add both W98 and W2K to tthe startup sequence.

You can manually edit the boot.ini file, or use the bootcfg command.

For details, check out the boot.ini page at www.systeminternals.com
or search Microsoft's site on the terms boot.ini and bootcfg

Chas

by lauragmc

Answer is a little confusing. When he refers to the C drive in the end is he referring to the original C drive for XP or the second hard drive as being C?

And is he saying to copy the files of the root folder from the original XP C drive to the second hard drive referred to as D?

by thechas

Sorry for the confusion.

You are getting the error because Windows 98 needs to install files onto the boot, or active hard drive partition.
Since XP is on your C: drive, and likely formated as ntsf, Windows 98 cannot write files to the boot sector.

The correct way to do what you want is to START OVER with clean formated hard drives.

Install W98 on the C drive.

Then, install W2K on the D drive.
Select custom installation so that you can install to the D: drive, and set up for dual boot with W98.

Finish with XP on the E drive.
Again, choose custom installation so that you can set up a multi-boot with 98 and W2K.

Chas

by thechas

This is option "B", a potential work-around to avoid re-installing XP.
It will require some extra work, and may be a little bit "buggy" at first.

If you have a spare hard drive, temporarily replace your C (XP) drive with it.
(this can be any IDE hard disk, however, I would use at least a 400MB drive)
Format the temporary C: drive as either FAT 32, or FAT16.

Install Windows 98 onto the D: drive.

Copy the files that the W98 instalation creates in the root folder of the temporary C: drive over to the root of the D: (W98) drive.

Then install W2K to the E: drive.
Select custom installation to set the install to use the E: drive, and to enable dual-boot.
Print out the boot.ini file that W2K creates on the temporary C drive.
Copy the boot.ini file onto either drive D: or E:
Also copy the files from the root of the temporary C: drive over to the root, or a seperate folder on W2K drive (E:).

Then replace the temporary C: drive with the original XP drive.

Your system will boot into XP, and recognize the new drive.
It will not know that you have 2 other operating system options.

In order to be able to boot into either Windows 98, or Windows 2000, you will need to manually add both W98 and W2K to the startup sequence.

Before doing so, make a backup copy of the XP boot.ini file on a floppy.

You can manually edit the boot.ini file on the XP drive, or use the bootcfg command.
(I think you can just copy and paste in the OS lines from the W2K boot.ini but, double check the command syntax.)

For details, on the boot.ini commands and syntax, check out the boot.ini page at www.systeminternals.com
or search Microsoft's site on the terms boot.ini and bootcfg

Hope this makes things a bit clearer.
Chas

by nickmkhn

For better reliability I wouldn’t bother with arranging such multiple boot with two harddrives involved.

Make a separate boot for every harddrive.
It’s not so difficult to choose the right HDD by changing the boot sequence from theBIOS when you need it.
It’ll save you much time and you won’t have a headache with the whole set of drives in case of one harddrive failure.
You system will be much more flexible and powerful in terms of reliability.
In case something happened and you changed your mind, you’ll be able to reformat, or repartition, or replace any of single harddrive. Easy to make a reliable full backup on unmounted drives. It’s very convenient from many points of view, especially when study new material, practice.

And if you are going to apply your knowledge into real world, I think it’s also good to build computer systems based on reliability and time saving models.

This discussion is closed to new replies.