Discussion Locked

Intel D850GB Motherboard won't boot

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

I am rebuilding a computer, and it won't boot. Here's the situation:

I had a PII computer that had all kinds of problems, so we decided to rebuild. I purchased an Intel D850GB boxed motherboard, Intel P4 1.7Ghz Processor, 2 Kingston 128MB RIMMs, and an ATX12V 350W power supply. I have connected the motherboard to the power supply with all 3 required cables, and when I turn it on I get memory beeps. I then installed the memory, terminators, and a PCI video card, and when I start it I normally get nothing but the processor and power supply fans spinning. Once in awhile I get video, but that might be one out of every twenty tries. When I get no video there are no error beeps, just spinning fans. I do not have access to an ATX video card, but my guess is that this is not the problem because it works occasionally. I have replaced the motherboard twice so far.

I have tried contacting Intel, but the company I work for doesn't want to pay for a phone call, and Intel does not respond to my email requests.

Any ideas? I appreciate any help, thanks!

23 replies

by dmiles

Does the power meet specs to provide enough power to components?
Check the memory modules to make sure they are seated properly and recognized by the system bios
Take out the video card and see will computer boot
Check the motherboard jumpers to check setting per the manual
Check the power supply to make sure the switch on the back is set for the correct voltage

by dmiles

Iam still leaning toward it being a ower Supply problem that is not working correctly and this being a special one,that I have no expierence with,yet you know it will make errors difficult to detect.
Sorry I cannot offer any soultions to this particular problem

by jfruits

Thanks for the help. I agree, new technologies suck when they don't work, but in the name of progress, I will not complain too much.

by jfruits

Power is ok.
Memory is seated ok (I just reseated it and the terminators to test).
Without video card, computer acts the same as with it (still no beeps). I also tried another PCI video card with no differences.
MB jumpers are ok. I have rechecked them a million times, and once more just now. Sorry I didn't mention that before.
Switch on power supply is ok. 115 which is right in my region.
Reseated the CPU. It looked ok, but I tried it one more time with no differences. I also checked, and there are no bent pins. Any other ideas.

by techkid

If you pulled out the video card, it won't boot (unless there's onboard video). If it's an ATX motherboard you should only have 1 power connector to the motherboard. The only things you need plugged in to the board to see if it works are the processor, RAM, video and power. If you have those components plugged in you should get to the post test if everything is working. If you don't get any beeps it's either bad processor or bad board. Those beeps are actually telling you something. They are called POST error codes. Here is a list of what some of the POST error codes commonly mean and how to fix them:
One beep, repeating - DRAM refresh failure.
Try reseating or replacing your RAM.
Three beeps, repeating - Base 64-Kbyte RAM failure.Try reseating or replacing your RAM.
Four beeps, repeating - System timer failure.
Try reseating or replacing your battery or motherboard.
Five beeps, repeating - Processor failure.
Try reseating or replacing your CPU.
Six beeps, repeating - Keyboard controller error.
Try reseating or replacing your keyboard.
Seven beeps, repeating - Virtual mode exception error. Try reseating or replacing your RAM.
Nine beeps, repeating - BIOS checksum failure.
Try reseating or replacing your BIOS and/or battery (if you don't have a soldering iron, or don't want to spend the time, try to replacing your motherboard)
One long beep followed by three short beeps - Memory test failure.Try reseating or replacing your RAM.
One long beep followed by eight short beeps - Display test failure.Try reseating or replacing your video card.
There is no standard for POST error codes, although the above list is generally correct, so you MAY not have the problem listed. Maybe you're not mounting the boards correctly and you're shorting them out?? If you don't have spare parts to swap with you better take it to a computer repair shop.

by jfruits

Thanks for the help. The lack of POST errors is killing me. I wish it was that easy!!! :-)

by jfruits

soulrider, TechKid, thanks for your advice. I should have clarified a bit more on my issue. I have been in the IT business 6 years, 4 of which included PC repairs at a reseller. The problem I am having deals with this specific motherboard. I am hoping someone has had experience with this board. Sorry if my original post was misleading. I do appreciate these answers, and I am not rejecting them because they have both given me good information to double check myself on, but unfortunately it has not yet solved the problem.

fyi...TechKid, the Intel P4 mainboards need a special power supply (ATX12V). This is not a standard ATX power supply, and it has a total of 3 connectors to the mainboard. It's really wierd (and kinda annoying).

Thanks again for the comments so far!

by jfruits

One more thing. TechKid, I agree with you. I don't rebuild PCs anymore, I am a Network Manager. Unfortunately, I am being given no budget right now so I can't take this into a shop or buy an AGP 2.0 card for it. I think that would solve the problem or at least help me diagnose it better, but others seem to disagree.

by still_learning

You did not mention whether or not you connected the harddisk drive, setting the jumpers to either CS (channel select) or MS (master). I would recommend Channel Select if your devices support it. I had a similar problem with a different motherboard, but was able to resolve the issue by disconnecting and reconnecting the drives. Hope this helps.

by jfruits

Thanks for the help. I appreciate the idea, but I do not have the drives hooked up.

by jfruits

Thanks for the response StillLearning. Unfortunately, the only things plugged into the mainboard are Processor, Processor Fan, RAM, terminators for empty RIMM slots, video card, and power supply.

by jfruits

Thanks for the help. I had already checked this site, but thanks for taking the time to post it!

by bohicam1

My thinking leads towards the ram. Is the ram you are using ECC ram or non-ECC. How is the ram setting in the bios? Also, regarding the terminators. The mobo's we have at work, if there are two rdram chips in, we do not need a terminator, only if there is one ram chip by itself do we need a terminator.
Good luck!

Mike

by jfruits

Thanks for the help. I double checked the memory (which is non-ECC) with the recommendations by Intel, and it is correct. They also claim to need the terminators.

by bly.akr

I know this will not be much of an answer but I am experiancing the same problem with a different mobo & cpu configuration. The only way I can get the thing to reliably cold boot is to press the reset button after the power button. It is a p233mmx with a Soyo mobo. I have 3 times sent this board & cpu back to the supplier & they insist it works fine. I have tried all kinds of different periferal components (ram,video,etc) & still the only solution is to hit the reset button after the power button.:(( I think there may be incompatabilities between mobo & cpu...that`s it.

by jfruits

Sounds like the buttons might be hooked up wrong. Sorry, but the issue sounds different than mine. If I find a solution, I will let you know.

by techkid

Another long shot.... it may be a defective reset switch that keeps sending a signal. Unplug that if it's connected to the board.

by jfruits

No switches are hooked up currently. They have been at times, but not now. I think I am going to consider this a loss of $450 and quit messing with it! (sorry for the reject, I already accepted your other answer, and it wouldn't be fair to everyone else if I accepted it twice)

by jfruits

Thanks for the help everybody. I am still stuck on this one, but I do appreciate all of the help. I am adding comments inline, and boosting the points to be fair to everyone. Once again, thanks for all the help.

This discussion is closed to new replies.