Discussion Locked

Laptop monitor wiring.

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Is there a way to wire a laptop LCD screen to a desktop PC? I have a LCD display from an IBM Thinkpad 365e that I would like to connect to a desktop pc (due to space constraints). Is this possible? If so, what is needed, and how is it done?

picture of the screen can be seen at:
http://mattsjunkyard.homestead.com/files/365elcd.jpg

Thanks for the help!

11 replies

by ann777

Cannot be done. The lcd connections are designed around the video adapter in the laptop. You would have to know how the IBM video adapter works to get anywhere and I'm sure that that is considered proprietary information.

by maxwell edison

It is possible, HOWEVER:

Unfortunately there is no simple solution for this conversion because the differences of the interfaces used in normal VGA monitor connections and the interfaces used in laptop LCD screen. The LCD screen on laptops typically use a special digital inteface between the graphics controller and LCD screen itself. Those interfaces can be special high speed parallel or serial interaces and there are many types of them in use. The graphics cards inside the laptops have thatspecial interface compatible with the display in the laptop, but normal PC graphics cards do not have this kind of interfaces. One problem is also that there is wide variety of LCD display interfaces in use, so first you need to figure out what interface is used and then get (somewhere) the necessary information on how to interface to it (information might not be publically available). Here is a list of some LCD screen interfaces used or in-use nowadays:

Analog VGA (used in external LCD displays but not in laptops normally)

44-pin TTL parallel

20-pin LVDS serial

Digital Video(6-bit for each color R/G/B) Sync Signal,DOTCLK, 4 pairs LVDS (used in some IBM laptop displays)

DVI (Digital Visual Interface LCD panel digital interface from DDWG, used for external LCD screen mainly)

So the conversion between normal PC graphics cards and LCD display taken from old laptop is not generally very complicated and usually not worth of a try.

To do the conversion you would first need to get to know what type of interface that LCD screen uses, then get the specifications of that interface, then specifications of that specific LCD and then design your own interface for that. Very complicated and not worth the problems. (Maybe a good educational experiment for a very good hardware/electronics expert, but not so for any average electronics homebuilder.(

(continued..)

by maxwell edison

.
.
It is possible, but in order to get the LCD to run off a standard VGA or standard digital video card, a converter must be bought. The converters cost about $250+. Its often cheaper just to buy a flat panel display. Regular flat panel displays on the market now are at least 15" which is much larger then the most laptop LCDs out there. The ready-for-vga flat panels for sale include the sort of input converter that you would have to buy to make the bare LCD work. While it seems like the converter should not cost half the price of a new LCD display, it does. The LCD interfaces that work for old laptop screens were made in low quantity for a few specific projects and are designed to support numerous types of LCD.

You can find specifications of some LCD displays and their interfaces from:

http://www.flat-panel.com/tech.htm.

(REMOVE SPACES from the pasted URL.)

ViewSonic has a reasonably priced flat panel 15".

Good luck,

Maxwell

by thechas

It might be possible if you have a video card with the DVI connector for LCD monitors.
You would also need a seperate power supply for the LCD biasing, and the back light.

You need a service manual for the IBM laptop to define the wireing.

This assumes that there is no other electronics needed to translate the DVI signal for this display.
There are electonics geek sites that have information posted on using surplus LCD screens for a variety of applications. These may give you further direction.

by jereg

I'm not sure I can enlighten anymore than the other answers, but maybe this helps. I've busted,er,disasembled several laptops during my, um...training. If you take apart the laptop lid with the LCD, you'll find that most mfr's put their specific video cards behind the screen. Then, a ribbon cable is run between the lid and the base, around or in the hinge. The ribbon cable plugs directly into the motherboard/system bus. a pretty simple and effcient setup. You MIGHT, if you can get power to the LCD, AND, if can find the pinout of the ribbon cable, be able to attach an extension with an ISA or PCI connector. then plug that into your PC. It MIGHT work. But that's just a guess based on the design of laptops. Ribbon cables can be really, REALLYfragile. Good Luck anyway.

by jereg

I looked at the picture that you posted. the cable with the wide connector plugs into the system bus. I believe that the video card will be behind the screen. Do as I described and it may work. It looks like there is a little connector. Power? mightbe a fun project.

This discussion is closed to new replies.