Question Locked

Loading Fail Safe Defaults Crashed My PC

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

It's an MSI motherboard (MS 6787 Ver. 1.0). I replaced the processor with a new one and started the PC. Then it showed message saying the processor was changed and need to correct the CPU ratio. Then I load the Fail Safe Defaults and restarted the PC. But it doesn't show anything on the monitor (no signal). I can see the processor fan is working. I replaced the new processor with the old processor again. But it behaves the same way.

Can someone please advice me on what I should do?

Thank you.
Matara

14 replies

by ismail.magued

first of all, replacing the cpu needs an updated bios.

note: you need to consult your msi agent have them send you a qualified
and i stress qualified technician.

let the technician meet with you and let him update the bios for you .

The technician may have to replace the bios on the motherboard as well

second of all upgrading a cpu in all cases
requires an updated bios.

if you upgrade the cpu than tinker with the ratios you could ruin the bios settings all together.

So please go through the steps above

call the msi agent first and ask for a qualified techician.

well if you need any further assistance or advice dont hesitate to message me back .
I check this post regularly

by rob miners

back to Default settings, by clearing the CMOS jumper. Restart the System and immediately enter the BIOS. It should automatically detect the new settings. Save the setting as you exit the BIOS.

Let us know how you get on.

by oh smeg

Was when you clear the BIOS you need to unplug the Mains lead. If you don't the BIOS will not be cleared as it is not getting any power from the Battery but from the 5 V DC Rail of the Power Supply.

So to clear the BIOS you need to unplug the
Mains Lead, and move the Jumper from Pins 1 & 2 to Pins 2 & 3 for about 30 Seconds. After that time has passed put the Jumper back on Pins 1 & 2 and then plug the Mains Lead back in and press the Power on Button on the Front Panel. You will be greeted by a Error Screen asking you to set the BIOS so enter the BIOS set the Data & Time and then save the settings as you exit the BIOS.

Col

by mkharis15

Thanks for the reply

Yes. I did so. But can see nothing on the screen. I only see the processor fan spinning.

Is there a way to re install the bios software?

by mkharis15

Thanks for your reply

I tried clearing the CMOS. But nothing comes on the monitor. I can see the processor fan spinning and nothing else. Is there a way to replace the bios software?

by rob miners

did you use CPU grease when you installed the new CPU?

Edit: lost track

by oh smeg

So assuming that it is the correct type remove the CPU and look at either the Pins on the Bottom of the CPU or the Pins in the Socket on the M'Board and see if there are any bent ones.

If there are whatever has the bent pins either the CPU or M'Board needs replacing as it is now nonfunctional.

This happens by incorrectly fitting the CPU.

Col

by mkharis15

Thank you for your reply,

Yes. It's bit older board. Pins are ok. I think it's something to do with the bios. If I can find a way to reinstall the bios, I think it would be alright.

Regards

by oh smeg

I have dealt with Bios Man in the past for all Server Bios Chips as I replace them rather than attempt to Flash the BIOS. It's just considerably cheaper if anything goes wrong to not have a Server down for any length of time.

http://www.biosman.com/

I have found them to be very good for my needs at least. ;)

Col

by mkharis15

No I didn't. But I don't think it is the problem. It should at least show something on the monitor and then go down if the heat goes up. But the CPU keeps spinning and nothing comes to the monitor. So I think it should be something wrong with the bios. Is there anyway that I can boot the pc from a USB pen even if the bios are not working? If then I can try flashing the bios.

Regards

by oh smeg

These Modern CPU's die when they get cooked. If the CPU has overheated it could very easily be dead and gone to [b]Silicon Heaven.[/b]

Depending on the type of CPU that it is the only safety measure may be if when you replaced the CPU you also replaced the Heat Sink/Fan as all of the new ones come prepacked with Heat Sink Compound on them. While the CPU will not die within the first few nanoseconds if there is no thermal contact between it and the Heat Sink it will die very quickly and in under 15 Seconds. ;)

Col

by rob miners

to heat. Even during testing you should use CPU grease. Try it again, this time using grease. Arctic Silver is a good brand and should give you five applications.

by rob miners

Remove the connectors to the Hard drives and CD/DVD drives. Check if it power on.

Test the Power Outlet or Power/Board by plugging in a radio or lamp.

Try another Power cord/lead if you have one.

Remove the Power cord from the PSU to discharge the Capacitors in the Power Supply. Then press the Power button for 10 seconds to discharge the Capacitors on the Motherboard. See if it will start. If it does start you can replace the (PSU) Power Supply Unit as it is faulty.

Remove the Power lead from the PSU, disconnect the 20-24 pin power connector from the motherboard. Reinsert the 20-24 pin power connector to the motherboard.

Swap the Power Supply unit for a known working unit if one is accessable.

Check the Capacitors around the CPU for swelling or bulging. They should have a flat head with a cross indent.

Clean the golden edge of each memory stick with a soft rubber/eraser, remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC.

Remove and clean the Video card with a soft rubber/eraser and then reseat it.

Remove all Add on Cards and see if it will start. Clean the add on cards before reinserting them one at a time and testing.

This discussion is closed to new replies.