Discussion Locked

Missing files?

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My computer has 3 hard drives, a 20GB, a 40GB, and a 60GB. When I try to boot, it finds a boot record on the 20, then claims that himem.sys, dblbuff.sys, and ifshlp.sys are missing. Then it says it can't find win.com. The computer has always bootedfrom this hard drive, and the only thing I have done differently lately is removing the 60 so I could ghost it on another computer. Why in the hell would it be doing this? I have important files on the boot drive, so I can't just reformat it and putwindows back on it. My system specs are
PII 450
327MB of RAM
Windows 98

6 replies

by ann777

Is this computer networked? ( I believe IFSHLP.SYS is from a network card install)

Since you are using Win98, it sounds as if your AUTOEXEC.BAT or CONFIG.SYS is not properly pointing to the above files.

Boot your system up normally, and theSearch for the files listed in your question. Write down the specific path that each file is located in (ie. c:\windows\system or where ever). Then make sure that either CONFIG.SYS or AUTOEXEC.BAT has the proper path to the file.... C:\windows\system\himem.sys . Then reboot and see if you get the errors again.

You should also have a path statement that has at least:

path c:\;c:\windows;c:\windows\system;

by ann777

Also, IFSHLP.SYS is probably called from either SYSTEM.INI or WIN.INI. If you do use a network card in this computer, I suggest you reinstall it.

by p. dickason, cne, mcse, cca

Dude, your windows directory is hosed. Those 3 files are normally located in c:\windows along with win.com and are called from config.sys. ifshlp.sys is the 32-bit installable file system manager, dblbuff is a compaq system driver and himem is windows memory manager but you probably knew that. Are you sure its booting from the correct drive? FDISK it and make sure the correct partition is startable. I can't believe removing a drive would whack your system, unless your \Windows was on that drive. Its possible that when you removed the drive, it was set as a master drive on the IDE and once you removed it,depending on how the jumpers were set on the secondary drive might have made itself the master and wants to boot from it. Check that just to make sure your booting from where you think you're booting. Hope this helps.
Pete

by wcp

I suggest you reinstall the 60GB HD back to where it was if no change was done to it.

If it works, then the Windows is actually booting from the 60GB HD.

If it doesn't, you need to reinstall Windows on top of the current one so you do not lose your programs and data.

Without Win.com, you cannot boot to Windows. Reinstalling Windows will take care of other missing files.

by thechas

I basically agree with wcp.

If you had ANY logical drives defined on either of the 3 hard drives, drive letters HAVE changed.

Windows cannot find the files where they used to be.

As wcp stated, the easiest fix is to re-install Windows.

Boot from your startup floppy, insert the CD, and run setup from the DOS prompt.

Make sure to re-install Windows to the original folder.

1CAUTION:
If any drives were setup with a drive / BIOS overlay program (such as Easy BIOS from Western Digital) you need to follow a special sequence to boot from a floppy.

In fact, if the 60GB was setup using the drive manufactures utilities, you may only need to run the drive utility program again to fix things.

It is ALWAYS best practice to remove hardware from device manager so that Windows knows that the hardware is no longer there before physically removing the hardware.

Chas

by csmith

This is no big deal.
The PC is not hosed.
When the 60 Gig was installed it, had the OS on it.
Windows decided, as it sometimes does, to stub C: .
Now in the boot process, it was using the MBR of C: , then jumping to E: for the registry.
The solution is simple.
Boot on a Win98 startup floppy.
Use the DOS command
sys C:
(At this point you might also want to use
dir C:
to check that there is nothing wrong with C: , and then
dir C:\WINDOWS
that all the files are in fact there in their proper directories.)
Pull the Win98 floppy out, and boot.
It should find the registry on C: and load Windows.

If it does not, DO NOT REFORMAT.
Back up C: from DOS.
Put the Win98 CD in the CDROM and run it.
A reload of Win98 over a corrupt copy of Win98 will usually work, with no file/data loss, except you may loose your Win98 updates. (The original system files will overwrite the updates if you allow it. To prevent this, select keep the newer file, when the warnings appear.)
The best solution is to put the 60 back in, and ignore this whole mess.
Backing up the PC is a good idea, regardless of what you decide to do.
Regards, Chris

This discussion is closed to new replies.