Discussion Locked

Modem not recognized after shutdown.

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I am looking for an answer to why every time my computer is completely shutdown and restarted it doesn't recognize the modem. The modem in question is a plug n play Voice/Fax/Data ISA type (5634BTV 56K V.90 Ready Modem PnP)using a TI chipset which came with the computer. Tech support from the manufacturer is non-exsistant since they went out of business. The one way I've been able to resolve this problem is to sometimes wait 3-4 hours and hope that it will be recognized again. However this doesn't work every time. The second way is to remove the modem card and then try to find the right position in it's slot for it too work again. I have two extra ISA slots available yet the problem still happens when I try those. Any help in finding a solution would be greatly appreciated.

9 replies

by dklippert

Type Sysedit on the Run line of the Start button. Take a look at Autoexec.bat and Config.sys. Sometimes "legacy" devices put startup information there and it can override Plug and Play. If you find any references, Put the letters REM in front so that they will not be used at startup.

by shanghai sam

Thank you for your comment. Below you'll find copies of what is found in my Sys. config. Editor. I don't see any "legacy" devices listed that could cause this problem. If you have any other suggestions I would be happy to investigate them also..

C:\AUTOEXEC.BAT
@ECHO OFF
SET BLASTER=A220 I5 D1 T4
SET TEMP=C:\ temp
SET DIRCMD=/O
PATH C:\BITWARE
c:\PROGRA~1\COMMON~1\NETWOR~1\VIRUSS~1\40~1.XX\scan.exe c:@IF ERRORLEVEL 1 PAUSE

=========================================================

C:\CONFIG.SYS
DEVICE=C:\WINDOWS\HIMEM.SYS
DEVICE=C:\WINDOWS\EMM386.EXE NOEMS
DOS=HIGH,UMB
FILES=30
BUFFERS=40
DEVICEHIGH=\realmode\btccdrom.sys /D:OEMCD001

by searogue

Hi, I have seen modems do this a number of times. Usually it is a bad driver, but can also be due to the modem being on the virge of going completely out. The fact that after waiting 3-4 hours does work sometimes tends to make me think the modem is just going out & the heat generated by the modem & other devices just enhances your problem. Things you can try: First, I would recommend that you pull the modem out & get a can of air & blow out the slot(s) that you intend to put the modem in, thentry re-installing the modem. Try the first slot & go down the line through the available slots.
Next thing to concider trying is to leave the case off the pc & put a small fan next to it blowing in while you are using the pc. If this solves it, youknow it is due to excessive heat. If neither of these work, I would suggest looking into purchasing a new modem. If you do purchase a new modem, now or in the future, BEWARE, do NOT buy a modem that says "Soft" or "Win" as these are software modems& will just cause you more headaches in the long run. Some well known software modems are: HCF,HSP,Conexant,Lucent,MDP,Motorola, even the BEST modem manufacturers (U.S.Robotics) has a software version of modem. Best bet would be a US Robotics model # 2977. I have been installing & using them for well over a year now & no problems at all.
Good luck,
Best Regards,
Tony

by shanghai sam

Thank you for your comments. However I have tried both methods you suggest. Although I do agree with you on the "Soft" or "Win" type modems and have tried both. The problems seems to be more involved than just replacing the modem since the modemhas been replaced once before and the problem still happened. Also the drivers have been updated to current ones or at least the latest ones I could find since the manufacturer went out of business two years ago.

by searogue

Hi again,
First of all, have you tried blowing out the slots ? sometimes the smallest amount of dust in them can cause problems, simply getting a can of air & blowing them out can sometimes do the trick. Have you tried putting a fan running into the case to ensure cooling, to determine whether or not the modem is just getting too hot? if it gets too hot, it will do just as you have described as well. From what you have told us here, I would definately have to suggest looking into buying a new modem due to the following: 1) the manufacturer went out of business 2 or more years ago, drivers (if found) will be more than 2 years old, which is technically out of date. 2)You say you have tried my previous suggestions except you did not comment on the 2 I re-listed. Common sense would tell a person that 1) if there is no support available from the manufacturer & problems arise that are not recoverable after seeking assistance from other support & knowledgable people, that it could be more trouble than what it is worth. or 2) it is not that important, rather, more of an issue of "bringing back the dead" than an issue of reasonable technical problems. 3) If you have replaced the modem before & it is still doing the same thing even with a brand new modem, maybe you simply have bad slots on the motherboard & need to look into getting a new MB.
Regards,
Tony

by yagar

The suggestions given so far are good ones.

I have had some stubborn modems. Occasionally I will get one to work by changing the BIOS setting. If you are using an ATX style mouse and the modem is trying to setup on Com 1. When in windows remove the modem in control panel /system. Reboot the computer and go into the BIOS and disable Com 1. IF you are not using it you can disable Com 2 also, it will just free up some of your resources. Boot to windows and re setup the modem and try it.
IF Com one is in use by the mouse as it an AT style MB do the above to Com 2 and leave Com 1 enabled.

In the process of all this try renaming the Autoexec.bat and config.sys (change the extension to 000). Win 9x works fine in most cases without any Autoexec.bat or config.sys . If you have trouble after renaming them you can rename them back.

good luck

This discussion is closed to new replies.