Discussion Locked

Modem Problems

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Hello, I recently purchased an external V.90 56K modem and installed it. However, ever sine I have installed it and set it up, I have been experiencing problems. Although it connects using the Windows Me Dial-Up Networking settings with no problem, after a certain amount of time it will regularly hang on me (i.e., it will stop downloading web pages, checking for new e-mail etc.). The only way to fix the problem has been to manually disconnect, reconnect, and then repeat this process each time it decides to hang. The same thing happens for large file downloads (i.e., files in the MB range) ? the modem will inexplicably stop sending information so that the download can successfully finish, and then eventually pop up an error message saying something like the download has failed, do you want to retry? (upon which the same thing occurs all over again if I select "retry"). I am almost positive that the problem is not related to either the phone line or ISP that I'm using to connect tothe Web, since I have another computer with another modem using the same line with the same ISP and it never causes me any trouble. Any suggestions or tips as to what might be wrong here would be deeply appreciated.

11 replies

by fenaikh

Hi
firat i would check conflict in IRQ.
start->run->(type) msinfo32.exe
check for confilct. expand the + to (down left) of the screen.

Check mdevice manger for modem resources conflict any yelow ?.

disable the com port IRQ3 and IRQ4 are for com ports
use IRQ5 2nd LPT.

Good luck

Mohamed

by galahad04

<< Check mdevice manger for modem resources conflict any yelow ? >>

According the msinfo32.exe diagnostic utility, there weren't any yellow-colored modem resource conflict, and no IRQ/COM conflicts.

<< disable the com port IRQ3 and IRQ4 are for com ports use IRQ5 2nd LPT. >>

The modem is currently set to COM port 1 (I am not sure how to change it maunally.) Thanks for your input though.

by liquidcoolit

More than likely it could be the initialisation string. If you go to Control Panel and Then Modems. There is an Advanced section there that will allow you to put in an initialisation string. Try some of these.
at&fx3
atx0
at&fx3&c1&d2
at&fx3s10=255
at&fx3s25=100
at&fx3&c1&d2s25=100s10=255

try those. Your modem sounds like its TTL is dieing prematurely. These strings should fix it.

Cheers ....

by galahad04

Thanks very much for your tip--settings at&fx3 and at&fx3s10=255 appeared to work very nicely and solved the problem of download aborting. However, they also introduced problems getting a successful dial-up connection to start. So I played around some more with the settings by removing the advanced settings and tinkering around with the modem configuration. It turns out that unchecking "Compress data" under the "Advanced" modem settings solved the problem. But in this case, I will award the points since you got me successfully 1/2 of the way there.

by curacao_dejavu

on computers with advanced power management this will happen. If you have setup the powermanagement options in the bios or in windows this will happen because the computer is idle for a long time and thinks that you are not working it will start thepower save mode after x minutes (whatever is setup). Set the power options to never (computer + screen) or a very long time. This won't happen on newer computers since they use another newer power management (I think its called acpm).

regards,

by galahad04

I don't think this is the problem, since under the Control Panel-->Display-->Screen Saver-->Settings, the settings for turn off monitor ang computer (what you mention above) were already set to never when I clicked to view the settings. I do know that the BIOS is one of the older ones and when I checked the Advanced Power Management settings, there was an option to recognize what port the modem was on. But thank you for your suggestion!

by otl

May sound simple, but.

Have you checked in the modem properties in start->settings->dial-up networking and the ISP connections properties

Increase the disconnect if idle for XX minutes and make sure the Don't prompt before disconnect is NOT checked.

by galahad04

<< Increase the disconnect if idle for XX minutes and make sure the Don't prompt before disconnect is NOT checked. >>

Thanks for your advice. However, I checked these settings as directed and it turned out that neither one was checked (both weregrayed out).

by grandhighdruid

I don't know if this will answer your question, but it might get you in a better path. Is the modem a WinModem? A WinModem is a modem that uses software resources instead of hardware. These are the epitome of evil, and should not be trusted. If it is, and you are having problems, you might as well give up. I have been fighting a WinModem for 3 weeks, and have still not had any success. Good luck!!

by galahad04

Don't think it's a WinModem, since under the "Advanced" settings in Modems in the Control Panel, Flow Control-->Hardware (RTS/CTS) is checked, not Flow Control-->Software (XON/XOFF).

This discussion is closed to new replies.