Discussion Locked

Motherboard Manufacturer

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Have an older Motherboard that I can't determine the manufacturer of.
It is an AT board with a 400 MGHZ, slot 1 processor. It has two PCI slots and two ISA.
It also has three ram slots. It supports AMIBIOS.
Are there numbers or other identifying markings, other than its architecture, to identify this board? I need the manufacturer and model, to obtain the correct manual to make a more knowledgeable installation.

9 replies

by bob

The FCC tag simply states that the board is compliant for home or office use. No numbers.

by dmiles

For an AMI BIOS use this procedure to determine the serial number:

Turn off the power.

Remove the keyboard or hold down one of the keys.

Turn on the system (you'll receive a keyboard error).

Note the serial number in the lower left hand corner of the screen. This is the BIOS identification string.
The serial number will look like this:

51-0102-zz5123-00111111-101094-AMIS123-P
With motherboards with BIOS from 1991 to Present the BIOS identification number for this BIOS identification string (the third set of numbers, in bold), would be zz5123.

DINT-1123-04990-K8
For Motherboards with BIOS from 1986 - 1990 the BIOS identification number for this BIOS identification string (the second set of numbers,in bold), would be 1123.

If the first letter or number of the third set of numbers for motherboards
with BIOS from 1991 - Present is:
or
If the first letter or number of the second set of numbers for motherboards
with BIOS from 1986 - 1990 is:

1, 2, 8, or a letter -- it is a Taiwanese manufactured motherboard
3, 4, or 5 -- it is a AMI manufactured motherboard
50 or 6 -- it is a US made motherboard (not AMI)
9 -- it is a Evaluation BIOS for a Taiwanese manufacturer.

To find your overseas motherboardmanfacturer, please look at the third (3) set of numbers in your BIOS string. Find the corresponding numbers in your BIOS string match them with the numbers below.

EXAMPLE:

51-0102-1101-00111111-101094-AMIS123-P,

by bob

This board is not in an assembly. It is just the board and processor.Boot screen information is not an option.
What I need is to identify the board, from looking at the board itself.

by bob

Yes, it would be the perfect resolve, if this board were in a machine and I could pull up the boot screen and retrieve information from there. The board and processor are Solo. No case and no hard drive, just the board.

by thechas

As stated by dmiles, the BIOS string is the ONLY reliable method to determine who made a motherboard.

The most common location for more information is on the outside of the last ISA slot. If there is not a sticker there that identifies the motherboard, you are likely out of luck.

Even many name brand motherboards have NO identifying information printed on the board itself.

Sounds like you have a 3rd party or OEM motherboard. Even if you can identify who made the board, you will be VERY fortunate to find a manual.

PC Chips made a lot of these motherboards, and they have removed ALL information for systems older than a PIII from their web site.

Here is a link to a TR article on identifying who made a motherboard:

http://tinyurl.com/h9hp

You should also give www.motherboards.org and www.wimsbios.com a try.

Take a close look at the entire board surface.
If you get lucky, there may be a model number printer on either the copper layer, or the silk screen on the board.

I am usually able to identify jumper settings and port pin-outs from looking at a motherboard.

If all else fails, take a picture or scan both the bottom and top side of the board and send them to me at thechas2000@yahoo.com

Chas

by bob

Thanks Chas,
This is what I was looking for.
I hope it doesn't become necessary to send you pictures of the board, but thanks for the offer.

This discussion is closed to new replies.