Discussion Locked

multiple hard drive installation on pc

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I would like to use multiple hard drives(quantity yet undetermined, prob. 4+) on some of the pc's in my lab. I have been told a couple of different things i.e. I will have to create a batch file or just daisy chain them. I have yet to get any specific answer on how to get windows (98/2000) to recognize them and how it will see them.

6 replies

by jlouis45

The maximum you can have is 4 harddisks on a PC running with win 98 / 2000 you can directly connect it to your motherboard. i.e. without any CD roms on your mother board you can put 2 HDD in IDE 1 and other other 2 HDD in IDE 2.

Do lemme know if your problem is solved.

by diskaus

I have 2 HDD on my pc Running win98SE i am using 1 Maxtor and 1 Conner i always thought it was a big job to get more than 1 HDD on your pc but WEhen i found out that Maxtor/Quantum and Conner/Seagate have thier own setup utilities supplied by Ontrack Data, if you go to the HDD manufacturers website you can download these utilities for free other wise go to www.ontrack.com but you will have to buy them from there , I know if you got to www.maxtor.com for Maxtor/Quantum and ww.seagate.com for Conner/Seagate if you look up the respective model numbers you can also get the jumper settings as well as all the technical data you need for those drives , but as for any other brands i dont know if they do the same thing.
I hope this gives you someidea , good luck

by fossil

Most PCs have 2 controllers built-in to the motherboard. Each controller is capable of handling 2 drives -- that includes hard drives and cd drives, but excludes the floppy drive(s). Since most machines have a CD, that would leave 3 available for hard drives. Each controller accomodates up to two drives by using the same cable. There are two connectors on the cable - a primary or master located at the end and secondary or slave located in the middle. They share the data path. Only one can be active at any given point in time. Reality is that this is okay in most cases. However, since the CD usually supplies data in large volumes or is busy playing music, it can interfere with a hard drive on the same cable and make access to that drive slow. If more drives or better performance are a strong consideration, you can buy additional controllers that add to the machine via PCI slots or as SCSI devices. Stay away from USB drives -- the traffic over the USB will generally slow thingsdown.
Often the drives will be recognized automatically at startup, after installation. If not, it might be necessary to enter the BIOS (easy -- read your manual ) and set the drive type to auto detect. With an additional controller, software (your "batchfile") might be necessary. Don't worry - the manufacturer will supply whatever is needed. Adding drives is simple. The most difficult part is handling the tiny screws so that they don't get lost in your machine. Just follow the directions slowly and carefully, and you'll be fine. It ain't rocket science.

by latlow

As far as Windows is concerned you can have up to 24 physical and/or logical drives (hard drives, CD drives, Zip drives, etc.) in the system. This is the available number of drive letters. 'A' and 'B' are generally reserved for floppy drives although on on some newer system BIOSs (from Intel for example) have removed the 'B' option. To physically add drives, you need additional controllers. IDE controllers, generally have two channels each. These days, the primary and secondary are on board. Second controller would give you tertiary and quaternary for a max of 8 devices. SCSI would allow for up to seven (or 15 with some) with each controller. If the controllers AND drives are configured properly, the system and Windows should detect and use them with no problem. Assuming one partition per drive, Windows will detect them and assign drive letters from 'C' to 'Z' in the order they are attached to the system. Master and slave on each IDE controller from primary to the end, and in a similar sequence for from LUN 1 to 7 for SCSI. With SCSI, one LUN is taken up by the controller.

This discussion is closed to new replies.