15 replies
by fin4lprayer Accepted solution
by older mycroft Accepted solution
Did you go any further into the innards of the PC ?
Did you clean out the heatsink? Check the heatsink fan?
How long has this machine been inoperative??
During this (??) period of time, has it been unconnected to the AC mains?
by fin4lprayer Accepted solution
by thumbsup2 Accepted solution
... because you don't have the skills or the tools to try and determine what component has failed due to overheating. They MAY be able to clean it up and get it working again. Then again, you may have already burned it up beyond repair, in which case you'll need to pay for them to replace components in addition to the cost of the components themselves.
Take it to a shop and ask for an estimate of the cost to repair it. They will charge you a minimum just to do the diagnosis.
by thechas Accepted solution
Removing the side panel is NOT a good solution to a computer over-heating.
Odds are that all you did by removing the side panel was allow the computer to run just enough cooler to function, but not cool enough to fix the problem.
Heat in a PC comes from multiple sources. The 2 biggest are the CPU and the power supply. When either fan starts to fail, the computer overheats and starts doing strange things.
I would not be surprised if either your CPU or power supply has failed.
1 thing you can check with the computer off is to see if all of the fans spin freely by hand. If by spinning the blade, the fan does not turn freely or stops spinning as soon as you stop pulling on the blade, then the fan is bad.
If the CPU fan has failed in this manner, odds are the CPU has also failed.
Same for the small chip-set fan on the motherboard. If it fails, the chip it cools will overheat and fail.
You have a choice, take the PC into a competent repair shop and let them diagnose it for you.
Or, scrap this PC and get a new one.
Depending on what has failed, you are looking at a minimum of $20 in parts plus the shop time. If the motherboard or CPU has failed, it could be well over $100 (US) to get this repaired.
Chas
by fin4lprayer Accepted solution
by thechas Accepted solution
Unfortunately, the easy way to test the CPU or power supply is to substitute in different "known good" parts.
If when you attempt to power up the PC your fans run and you can hear the hard drive and optical drives spin up and go through the normal POST sequence, odds are that the power supply is good.
As to the CPU, I did notice the other posts. Did you just pull off the heatsink with the power CPU attached? Or, did you release the lever on the CPU socket?
Some thermal pastes are pretty sticky, and if the CPU was not properly seated in the socket, that might be enough to allow the CPU to pull out.
As long as none of the pins on the CPU are bent or broken, you can see what happens when you install the CPU back into the socket and apply new thermal paste prior to turning the system back on.
Perhaps all that was wrong is that the CPU was not properly installed in the first place.
Chas
by .martin. Accepted solution
the CPU.
in an earlier post you said you cleaned the heatsink (or fan) on the CPU, when you did this, did you take it off? when you put it back on did you apply thermal compound?
most likely you will have to take it to a local computer shop, where they should be able to fix it.
by fin4lprayer Accepted solution
I took off the fan on top of heatsink, and cleaned that...i jsut went back a few minutes to try to get a look at the cpu. When i take off the heatsink, (im not sure how to describe this since i dont know everything about computers) on the bottom of it is the green square with all the little golden prongs. that is on the bottom of the heatsink...and im not sure its supposed to be like that because im looking at some pictures, and that thing i am describing is on top of the white thing w/ the lever on it, and not on the bottom of the heatsink...im not sure if its supposed to be like this or not.
But no, i didn't apply any thermal compound or anything.
by older mycroft Accepted solution
What you are describing sounds like when you removed the heatsink, the CPU came away with it (all those 'little golden prongs' are the legs of the CPU).
If you didn't release the lever prior to removing the heatsink, you have effectively pulled the CPU out of its socket. One possible reason for this would be that the CPU has welded itself to the underside of the heatsink. If this is the case, your CPU is now toast - beyond repair.
If you can prise (GENTLY) the CPU away from the heatsink, you should use a piece of plastic (something like a Store Card) to remove whatever thermal compound is still attached to the top of the CPU and the bottom of the heatsink. If the CPU shows signs of blistering it's a gonner.
Whatever you do in terms of rebuilding the construct, you'll need to get hold of a syringe of thermal compound, so that you can reassemble the components that you've just taken apart.
by fin4lprayer Accepted solution
by older mycroft Accepted solution
I'm afraid your system has suffered full meltdown.
If the CPU has in fact melded itself to the heatsink, your system is irreparably damaged, the question now is - did the heat damage extend beyond the CPU / heatsink ? Mostly the heat damage will be restricted to the CPU but I would advise that you show considerable thought to the motherboard components. ANY capacitors that show signs of bulging (or bleeding! - [b]*if they are bleeding DO NOT TOUCH THEM![/b]) would generally indicate that the motherboard has gone south also.
[b]* The electrolyte within any capacitor, when it 'bleeds out' is injurious to human health! Believe me![/b]
You may be looking at an almost complete system rebuild. ;)
by fin4lprayer Accepted solution
by ---tk--- Accepted solution
If you torched your system, I would rebuild a close to new one.... and learn how to put it together. Its probably easer than you think, just remember the square cant fit in a circle!
you already have the Monitor, case, Power supply, the HDD, and possible a graphics card... so all you need is a motherboard CPU and RAM... by building a new one, you can seriously save some money...
by oh smeg Accepted solution
Put the CPU & it's Heatsink back in. Did you lift the lever slip the CPU back in with the correct orientation so that the legs went into the corresponding holes in the socket and then lock it in place by dropping the lever?
If you did all may not be lost as some Heatsinks get bonded to the CPU with a special Glue that transfers heat. If you didn't put int back in that way odds are that you destroyed a perfectly good CPU to begin with.
Next have you removed the RAM & Video card? If you have not just unlocking these and pulling straight up till they come free and then pushing them back in will often cure any problems particularly when the case is left open and allowed to suck in Dust and other rubbish and even worse have air directed onto it so that things get blown in doing damage.
Generally speaking you [b]Do Not[/b] need top touch the CPU buy you should clean it's Heatsink with Canned Air and prevent the Fan from Spinning.
When you press the On Button before lifting out the CPU what actually happens? If the fans run lights flash on and ff or stay on and you hear beeps the unit is running and it very much sounds like a Bad Connection between either the Video Card and RAM to the M'Board. Lifting and reseating these should fix that problem but if they are heavily corroded you may need to wipe them with a soft rubber/eraser to clean the contacts.
Actually knowing what type of CPU is fitted here would be nice as it could be anything from an old Pentium to one of the P4's or Socket A AMD's. Anything newer has a different locking system for the CPU so it can not pull out when you lift the Heatsink.
The other thing that could have happened here is that the Power Supply has carked it and one or more of it's circuits have failed. If only the Fans where running and there where no beeping sounds coming from the Case at the very least only the 12 V DC Circuit is running.
If you leave the Monitor switched on and then press the On Button of the Tower and you see that message that the Monitor is Disconnected you have a Shot Power Supply and it needs replacing. I saw one like this where the owner had bought and fitted a new M'Board, CPU, Video Card, RAM and Video Capture Card and made no difference. This was because the Power Supply was shot but he thought because the Fans ran and the LED lit that it was OK. A very expensive mistake as he effectively bought another computer without first testing the Most Basic Part to see if it worked. It would have saved him Hundreds of $ to just plug in another Power Supply and see what happened when the On Button was pressed.
Col
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending