Discussion Locked

My pc does not see all of my 20GB drive

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi all,
I have a Pentium MX 233MHz, SQ576 motherboard w/ Intel 82371 AB/EB chipset. I just bought a Western Digital 20GB drive to upgrade my HDD, but my pc does not see it. I tried the disk manager program from Western Digital, but after I installed Win98 there's a problem with my Secondary IDE controller (doesn't work so my CD-ROM is not even present). I tried fdisk to partition the drive, it only saw 8GB. Is there any other way to partition my drive so my pc will see all 20GB and can work with all the partitions? I'm planning to install Win98, WinNT, Win2K, and Linux.

Thanks for your help.

15 replies

by thechas

You can check the motherboard mfg for a bios update to handle larger drives.

My recommended option would be to install a PCI slot IDE controller card. They cost around $30 (sometimes less).
The biggest advantage of the controller card for you would be that you will get the full data transfer rate supported by the drive.
At best, your motherboard has an UDMA 33 IDE controller. So, an ATA100 controller card would tripple the data transfer rate.

I suspect that the WD utility was blown away by the Windows installation.
I know with the older utility, you had to go through a specific boot sequence to boot from a floppy. You need to let the utility load from the hard drive before you can boot from the floppy.

With your plans for 4 operating systems, I would set up the drive with 5 partitions.
1 primary partition for W98.
1 extended partition with 4 logical drives.
1 for each OS, and 1 shared drive for data files.

You may also want to get this boot utility to aid in setting up your multi-boot system.
http://ourworld.compuserve.com/homepages/gvollant/bootpart.htm

Remove any spaces from the pasted link.

Chas

by thechas

As to the IDE controller problem, download and install the drivers from Intel for the chipset.

Chas

by bjbolton

I'm sure your machine can handle the hard drive and all four OSs. Unless this is a test, but my advice to you would be to buy faster and more update-to-date machine for better performance and reliability.

by joseph moore

Was the new drive partitioned in FAT? The reason I ask is that FAT had a limit of 8GB that it would see; FAT32 could go higher (32GB as I remember; NTFS goes up to 4 terabytes, luckily!) So, if you formatted it with normal FAT, then 8GB would be allyou would see.
I have set up Western Digital drives using their software, and I know they have FAT32 as a setup option. Set up the drive again, and make sure you are using FAT32.

hope this helps

by whatnetever

To TheChas:
Thanks for all the ideas. I think I'm going to try the IDE Controller Card. My only question is, is this going to make my pc see all 20GB, or is this only a solution to my 2nd IDE controller not functioning in Win98?
Also, I have tried the Intel site for IDE controller drivers, but it only said that with Win98 the Windows drivers are to be used, so I'm stuck here...

To Joseph Moore:
Thanks for the input. I have used FAT32 but it didn't do anything different, even though FAT32 is "supposed" to support up to 40GB.... At this point, the BIOS is calling the shots, I guess.

by john.m1

the other guys have just about covered it but, for future reference to uninitiated readers, when we save money by buying an OEM drive we don't get the install disk, with it setup is a breeze, the bios is updated and we get the full *GB size of the drive. I am not sure if getting hold of the floppy is that difficult but you need to try.

by nickmkhn

My suggestion never apply any Disk Manager program or EZ-BIOS on your new investment, cause they might bring you another problems, and it’s difficult to get rid of those utilities completely.
I used to work on similar Pentium motherboards and still have at least three of them. There’s no a newer BIOS upgrade for them. Buying a new IDE controller board for such obsolete hardware isn’t a smart decision, cause for ~ $40 you can buy a new Celeron-T motherboard from ECS Elitegroup, FIC, etc. or a used P-II motherboard with a processor that would give you more advanced features for your buck.. Anyway, an IDE controller can solve all the problems with attaching a new large harddrive to a relatively old motherboard. But be aware, that with the old you have it sometimes brings some compatibility and other problems.

What I always do with such old motherboards, just boot from Win2000 installation CD (set in BIOS the proper sequence first), and the Win2000 recognizes a HDD above 8.1 GB. I go through the installation procedure until the option to create/delete/format partitions. I partition my HDD on smaller parts, then format C: from there, and exit.
The drive is ready for installation of everything from MS, even UNIXSolaris.
No money involved, no BIOS screwed up, no new harddrives spoiled with EZ-software.

by nickmkhn

Ther’s some more. On my Dell Optiplex XL-575 (i430NX, March 1994, Pentium 75 overclocked to 100MHz @ 66MHz FSB) there’s no such feature as Boot from CD-ROM. What I did: pre-partitioned and formatted a 20GB IBM harddrive on a newer machine first, then installed Win98SE, WinNT and Solaris7.

Buy the way, I just tried to attach a 40GB IBM HDD partitioned on 5-16GB partitions from another machine, and my oldie recognized it. But on newer (1996) i430VX machines it worked only up to 21GB though.

by nickmkhn

Also just you to know that there’s a known compatibility issue with new Western Digital harddrives starting from Wd -bb series (no problem with older –aa series) on some motherboards.
Those who got problems have to call WD support and they send their special ribbon cable.
Or there’re some work-around with cutting Wire #1 (and #2 on 80-wire-cable), just see your HDD p/n, and check the web on recomendations.

This discussion is closed to new replies.