Discussion Locked

New ATA100 Controller

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have an old 266pentium II pc with a 4gig hdd using windows 98. I just received a 40gig WD hdd 7200rpm ATA100. My mobo controller does not support the new drive so I purchased a basic Ultra IDE ATA100 controller to plug in. After running the install disk and unplugging my 4gigHDD (primary) + cdrom (secondary) from the onboard controller. I place the new controller in the pci slot and re-connected the 4gig hdd and cdrom to the new card. The bios sees the controller but the controller does not see the hdd or the cdrom. I went as far as disabling my onboard ide controller. This allowed the controller to see both drives but now it fails to boot to windows. It hangs at the windows 98 logo screen. When I press escape to get to the C:\ I'mable to see all my directories but I'm unable to launch windows even from dos. Any suggestions on how to make this card work? This is the second card, I took the first one back thinking it was the card. DESPARATE FOR HELP!!!!!!

9 replies

by dont-bother

Ain't this a terrible situation? They want to sell IDE Controllers, but they don't want to pay for Microsoft certification, and they don't really want to support it either.
I had the same problem with a SIIG (ACard chipset) IDE Controller.

You have to remove the drives and MB IDE controller in Device Manager first, if you don't want to use it.
You'll also want to put your CDROM as primary on secondary channel of new IDE controller. If you put it as secondary on same channel as the HD, you won't get full ATA 100 speed from the 40Gb HD.

Windows won't load the way you describe because IDE Controllers are numbered 0, 1, etc.
Windows still thinks your IDE Controller is 0, but the new controller install software assigned it as 1.

Also you need to check the max drive size Win98 can handle. Can it handle 40Gb? Even if it does, I'd repartition the new HD to smaller sizes anyway. Even at 10Gb partitions, each file on your hard drive would take up something like 18k or 32k PER file.If you partition your virtual drives C:, D:, E: etc with a partition size of 7766Mb (slightly less than 8Gb each) each 1-byte file would only take up 4k bytes instead of 32k.
Much better use of hd space.

Essentially what I'm saying is I would
1.) remove the CD and Hard drives, controllers from Windows Device Manager.
2.) Install ONLY the new 40Gb HD - FDISK it - format it - and install Win98 on it.
3.) After its working, then install the 4Gb as secondary drive on same channel and install CD as primary on secondary channel.
4.) copy what you need/want from the 4Gb drive to the 40Gb and then remove the 4Gb (a slower speed drive on the same channel will ONLY slow things down).

Sorry, I know that probably what you didn't want to hear, but IT WOULD be the better way to go.

Hope it helps.

by phauser

Knight,
Outstanding answer. Thank you for your for your help. I agree with the partioning size 100%. I thought about just setting up the new hardrive as fresh install but I have apps on my old drive that I dont have the install disk for them. Ithought about after I got the controller setup and it was able to see the 4gig hdd. I would ghost the 4gig to the 40gig. Do you have any thoughts or advice on this procedure? Also I plan to upgrade to xp as soon is I got everthing running. THANKS ONCE AGAIN YOU HAVE BEEN A BIG HELP.

by dont-bother

The only reason 'ghosting' the 4Gb to the 40Gb wouldn't work is because of the 'registry settings' that Win98 has for the hard drive and controller. If you do that, it's going to be looking for the 'wrong controller'.

It can be done, but you'd need an external program like 'Partition Magic' http://www.powerquest.com
or something similar.

Partition Magic just released version 8, which sells for $70.

The cheapest and simplest way is as described, but if you don't have the 'install disks' for some of your programs, then maybe the $70 or so would be worth it?

Good Luck,
Steve

by thechas

For information on partitioning your drive, check out the partitioning information at www.aumha.org

or the fdisk page at www.fdisk.com/fdisk

As to partition size; using fdisk you enter the size in decimal bytes.
An 8 GB partition would be 8192 MBytes.
I subtract 4 - 8 from the maximum, as fdisk adds a couple most of the time.

I would also recommend re-enableing your on-board IDE controller.
Connect your CD-ROM drive as slave on the first channel, and if you have 1, your CD-RW as master on the secondary channel.

For most IDE controler cards, you need to install W98 before switching the drive over to the controller, and then switch over to the controller, and install the Mfgs driver.

For XP, you will be prompted for the driver for your 3rd party IDE controller.
Your CPU is a little slow for XP.
Check with your motherboard mfg as to what is the fastest CPU you can install, then check out the prices on used pulls at www.compgeeks.com
I would also max out your system RAM for XP.

Chas

by vic66

I have similar problem when I install my ATA100 controler. In my case, I just unplug my cd-rom from the controller and put it on the onboard controller and leave the big HD on the controller because some of the controller doesn't support CD-rom.

This discussion is closed to new replies.