Discussion Locked

New hard drive not detected

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Installed a new WD hard drive. The drive is 40G @ 7200RPM and is set as the master with a slave on IDE 1. The old drive is a 6G @ 5400RPM and is set as the slave on IDE 1. IDE 2 only has a CD-ROM set as master without other drives. The new driveis attached to the first 40 pin connector and the old drive is attached to the last 40 pin connector. The red stripe on the cable corresponds to pin one at all interfaces. The power is connected properly. The system consist of a Gigabyte GA-686BX MB, running a PentiumII @ 350Mhz with 448M of Ram. The video, sound and modem cards are connected as follows: AGP,PCI,ISA. The BIOS is Award 686bx f1f; although it still shows version 4.51 at the top of BIOS setup, with 686bx f1f shown at boot further down the page. The new drive has Windows 98SE and the old drive has Windows 98SE and Windows 2000.
When I first installed the drive everything worked fine, including all of the restarts with the loading of a new OS. However, upon cold boot thenext day none of the hard drives were detected by the BIOS. I restarted several times with no effect until I powered down while in the CMOS setup and the drives were detected upon power up. This did not last and the next day I could not boot, as the drives were not detected.
I tried the old drive on its own on both IDE's and it worked fine. I did the same thing with the new one and it only worked here and there. I tried several different setup arrangements with jumper settings and cable locations with no avail. I eventually put the PC back to the first configuration and set the CMOS settings of the drives manually. The drives booted once, but would not on a cold boot. I later discovered that if I started the PC while having the power disconnected to the new drive and then giving it power after the post "all good" beep, everything works fine and the drives are detected then my OS loads.

13 replies

by thechas

I have had a similar problem with 2 different MBs.

The only common item between systems was WD 7200 RPM drives, and a no name S3 Savage 4 AGP video card.
So far, changing the graphics card has corrected the problem.

I haven't come up with an explanation as yet. So, for what it's worth, try a different video card.

by telspee

All were good answers, but in the end, it turned out that the hard drive was shot.

Thanks a lot!

by grump

Here is my input..

More than likely the new 40 gig dirve is Ultra ATA 100 and really not support by the system BIOS. Also you will need to be using the 80 conductor on the dirve..

Try connecting the old drive on IDE1 Master and you cdrom as slave..
The 40 gig drive on the IDE2 with the 80 conductor cable and see what the results are.. Some drive manufactures also have utility diskettes with the drive and allow you to change the ATA 100 to ATA66 which will work well in the older system.. Good Luck.

by telspee

I tried your advice with no avail. The BIOS detects the drives if I plug the power in to the master after post. I tried WD's utility with ATA 33,66, and 100. I am wondering if maybe this all has to do with the drain on the power supply.

Thanks,
telspee

by dmiles

Check for a bios update for the latest flash support,check the bios manufacturers web site
Open the CMOS panel and set the drive configuration to AUTO
Check the Microsoft knowledgebase web site and see if the ATAPI update will be of help

by telspee

Flashed the BIOS three separate times and my CMOS is set to auto. Current BIOS is ATAPI compliant.

Thanks,
telspee

by dmiles

Check the Power Supply output,with the number of devices that you have installed it would be a good bet that the power is being pulled down,you most likely only have a 250w Power Supply and this can cause a problem with the faster ATA drive

by telspee

All were good answers, but in the end, it turned out that the hard drive was shot.

Thanks a lot!

by diamond dan

Hi,

This definitely looks like a power issue. Especially in view of the fact that the drive works correctly if you only supply power to it shortly AFTER the rest of the system has started power up. Reason being: any electrical engineer will tell you that on turning on any component with a motor (ie hard drive, CD-ROM, etc.) there will be a large initial drain on the power source. This drain is in the form of available current in amps. An increase in the amp load causes an inverse drop in thevoltage supplied. With inadequate voltage, some components that identify your hard drive during startup may not function properly. By applying power to your hard drive after the rest of the system starts you are spreading out the demand on current and allowing the voltage to be supplied at a more constant level.

What you need is a beefier power supply, just make sure that it is compatible with your current configuration. Consider both type (AT vs. ATX) and size considerations.

Also, don'tworry if your new drive is ATA-100 and your BIOS is not. The drive will simply operate at the highest speed supported by the BIOS, controller, and cable. There will be no compatibilty issues, you just will not get the ATA-100 data transfer rates, itwill be transferring at a slower speed.

Regards,

Dan - A+, Net+

by telspee

All were good answers, but in the end, it turned out that the hard drive was shot.

Thanks a lot!

This discussion is closed to new replies.