Discussion Locked

No screen signal after replacing harddri

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a 1.8 GHz P4, with a 64 MB Geforce TI 200 graphics card, 768 MB SD RAM, and a brand new 160 GB Seagate harddrive after replacing the old harddrive that broke. When I start my system, no matter what CD's or floppys (XP install CD, XP boot floppys, 98 boot floppy) I put in the drives, it does not boot. It seems like everything is running and powered, the cords are fine, but the screen display nothing, it does not even recieve a blank signal. Please help, I have no clue on how to get on.

14 replies

by thechas

Start by triple checking all internal connections.

Make sure that the IDE cable is installed correctly.

Make sure the master / slave jumpers are set correctly.

Remove and re-seat all RAM modules and your video card.

Inspect all plug-in cards and cables to make sure that everything is seated properly.

Chas

by stress junkie

Also check to see that the motherboard CMOS settings
are correct. Check to see that the motherboard shows
the correct make/model of the new hard drive. Also
check the boot sequence to see that CD-ROM, and
possibly floppy drive, are set before the hard drive in
the sequence of boot devices.

by jma_polarforsker

You missed a point, I can't enter BIOS (or if I can I have no idea what I eventually will be doing), the screen does not display anything, I have pressed both F1 and DEL on "startup" and the screen does not get any signal anyway. As far as I recall the boot sequence is good enought, I have booted from CD before.

Made me think, my old disk had 3 partions, CDE, so my two optical drives was named FG, could this have altered with the new disk, and could that have caused my system to be unable to boot from them? Anyway that doesn't explain why the floppys didn't work, actually I think it never read from the floppys, hmm check cables once more ... nope, they seem to be fine.

by jma_polarforsker

I have been unpluging, pluging and checking all day, video card have been in and out 100, I have removed a RAM module and the modem and I still get the same result. Harddisk is spinning fine, so is the DVD drive, they are by the way connected using the same cable, with DVD drive in the end, and the harddisk in the middle. I have a jumper on the left slot in the harddrive (master/slave slot), just like it was placed on the old drive.

by burtonizer

Hi there,

I would try putting your "old" hard-drive back in and setting your "new" hard drive as the slave. This would allow you to at least get into your BIOS settings and also allow you to FDISK and format the new drive. Once you have done that, make the "new" drive master, make sure it's on the end of the ribbon cable and your CD drive is on the middle connector and try getting into your bios then. Triple checking your ribbon cable, etc is connected properly.

Hope this helps, it's what I would do!

by jma_polarforsker

I tried putting in the old drive instead of the new, the old one used to work for about 5 minutes, but now this configuration neither works, even though it used to.

by lmayeda

Long shot. What kind of monitor are you using and do you still have the manual? I just moved a Sony Flat panel from one PC to another and encountered black screen. After reseating the video card and replacing the cable, I decided to read the manual. One of the buttons on the screen "INPUT" toggled through about 4-5 options, one of which resulted in a signal. I figure that changing the hard drive is similar to switching CPUs so I hope this might help.

by hloke

Hi, have you resolved your diaplay issue?
Some trouble-shooting tips for you to look into it. From your explaination, it sound like you have done all steps but there are still few things you have over look.
1. Please check the monitor signal cable. Make sure that the 15 pins connector, none of the pin is bent.
2. If you observed the monitor signal cable socket, it looks like D-shape. Make sure it is plug-in in the right direction to the display card socket.
3. Does your monitor works if it is plug to another working PC?
4. Double confirm that the harddrive ribbon cable is connected in the right direction, pin1 to pin1.
Hope the above tips will help you to identify and resolve your problem.

by jma_polarforsker

All 14 pins seems ok, I tried a different monitor anyway, no result. I don't see how I could plug it in in the wrong direction. The ribbon cable is also idiot proof, only one way to plug it in.

By the way, I have also tried another video card, no better.

To all of you: Thanks for your time and your suggestions, it's kind of you to try to help me. I guess this is not something that can be dealt with over the internet.

The only thing that I can think off altering now is all the jumpers, I think there is about 4 on the mainboard, and of course 4 slots on each drive.

I'll get someone to look at it soon.

by hloke

Sorry to mis out one more tip.
By the way, how old is your PC? Have you check the CMOS battery? A run-out battery will cause no display as well.
Hope this last one will help you to solve your problem.

by jma_polarforsker

I had 'someone' checking my computer, and he found that one of the processor pins had melted, presumeably due to an overload. So no matter what caused what, both processor and mainboard will have to be changed.

This discussion is closed to new replies.