Discussion Locked

Northgate/AMD 1.3GHz "Powers Down"

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
We have a Northgate PC with an AMD 1.3GHZ processor. I do not know the mainboard manufacturer or the specific model of the AMD, sorry. The machine acts as if it has lost power (screen goes black and then to "Power saving mode" and the light goes from green to amber). The machine still has power (lights are on and the fans are turning). I assume the problem is 1) the power supply, 2) the processor or 3) the mainboard. Any other suggestions? When booting the machine will get as far as the BIOS load to the Windows flash screen but seldom any further. I have turned off all Windows and BIOS power management but that only seems to have made things worse.

18 replies

by ann777

4) Probable hdd failure.

Have you tried booting from floppy drive?

The fact that the power remains on but the computer gets through POST, bios and "loads to the Windows flash screen..." tells me that your Windows software install may be bad on the hdd or that the drive itself has a problem.

by sgt_shultz

i vote for the processor...check the processor cooling fan (sounds like you did but maybe it is intermittant)... and then make sure the CMOS settings for the drive/IDE controllers are still correct
good test for whether it's windows or non-periperal hardware might be to boot to floppy and let it 'cook' for a while, see if it fails. if it does, it's not windows (course you have to wonder what damage might have happened to the windows install because of these crashes...) suggestion for boot floppy to use: the one with diagnostics for your harddrive, like maxblast or wddiags...

by al

While extremely skeptical, I created a boot floppy on another machine and booted from it. The sick machine ran fine and I could do a whole hdd Scandisk surface analysis without problem. So, I reinstalled Windows just for the merriment. No change once I tried to boot from the hdd. I am going to try an FDISK /MBR since I now think the problem lies somewhere between starting to boot and loading good old Windows itself. My question is: what actually lies between the mbr and win.com? Is there more than boot.ini? I THINK I know what boot.ini should look like.

by thechas

Another 'fix' for Socket A motherboard problems is to manually set the CPU frint side buss and multiplier settings in BIOS setup.

For whatever reason, socket A CPU's hate to be under-clocked.

Mnay motherboards set the wrong default settings for the FSB and Multiplier.

If you have SDRAM, and the 'rated' FSB for the CPU is 200MHZ, the settings are:
FSB 100MHz, Multiplier 13X

266MHz FSB, and PC133 SDRAM:
FSB 133MHz, Multiplier 10X

If you have DDR RAM, and the 'rated' FSB for the CPU is 200MHZ, the settings are:
FSB 200MHz, Multiplier 7.5X

266MHz FSB, and PC133 SDRAM:
FSB 266MHz, Multiplier 5X

Chas

by sgt_shultz

if possible, we need more info about your problem. when you say windows flash screen, are you talking about the white text menu on black background? (if so, you are getting as far as boot.ini in the boot sequence) what os are you on, exactly and what service pack level? how big is your hard drive? are you dual booting any other os's? did this ever used to work? did you upgrade your hard drive?

by al

I hope you find this a fascinating as do. First, the machine will run for hours when booted from floppy, at least 16. This is how long the Norton virus scan took. The ?good news?: no virus. Second the machine will boot to Safe Mode and appears to be stable. There is one case in which it will not work in Safe Mode. Occasionally a message box appears that says the Display configuration is incorrect and if I don?t cancel that within a second or two the ?power off? condition occurs. I discovered that every device (almost) appeared more than once in Device Manager and some (the monitor) had four entries. I deleted everything and booted ?normally?. Windows Setup started and appeared to complete set up (I had earlier tried reinstalling Windows). However there were still no devices in Device Manager but at this point Windows (ME by the way) had run ?normally? for five or ten minutes. I was told to reboot and did and Windows started finding devices. While in this process it ?powered down?. I booted to Safe Mode, removed everything again and booted ?normally? and as soon as Plug and Play starts the machine ?powers down?. The machine has an on board display adapter and I am going to try a plug in but I think the problem is in the mainboard or drivers and I am inclined to mainboard. Any ideas?

by al

The add in video card made no difference in the behavior of the machine. It looks to me like it is either the processor or the mainboard. Since the machine will run for hours booted to DOS and okay in Safe Mode I am inclined to believe it is the mainboard and some feature on it. Is my logic valid?

by thechas

Sorry it took so long to get back to you.

From your description, I do not believe that you have a hardware problem.

Check the ACPI and power savings settings in BIOS setup.

Then, I suggest that you boot from a startup floppy.
At the DOS prompt, run fdisk /mbr
Then run fdisk again, and delete ALL partitions.
Re-boot, and partition the drive as desired.

Re-install Windows.

Chas

by al

Your suggestion intigued me so I tried it and the machine responded exactly as before. So I tried resetting the BIOS, then deleted all the partitions, recreated them, formatted the hard drive, reinstalled Windows and now I can even boot from floppy! I was going to search around from a BIOS flash but now I think this baby is toast. Any thoughts?
Al

by thechas

Reading through the other posts and your comments, I have to agree that the system is, as you said, toast.

Most likely a bad solder connection on the motherboard, or a failed IC.

DOS doesn't load drivers, and ignores much of the chip-set on a modern motherboard.

I have a few motherboards with 'strange' hardware problems.

1 works fine IF I do not enable the USB port, or install a sound card.

Another refuses to boot and shut-down properly, no matter what.

One last thing to check, look at the capacitors on the motherboard.
Any signs of bulges or liquid leakage?

If so, you are the victim of a bad batch of capacitors made in China.

A large number of motherboards were built with a batch of capacitors that had an unstableelectrolyte in them.
Over time, most of these caps fail.

The big problem, is that many manufactures are not admitting that they are affected by this problem.

I would try a new motherboard, and see if you can recover the rest of your hardware.

Chas

by al

I hope you love this little follow up. The user who had this problem, we found him a spare machine to use while I tried to figure out what was going on with this one. He complained that he could not connect to the Internet. He was right. So I tried a couple of little things, one of which wanted a reboot. The machine will only boot to Safe Mode. As I looked around I discovered that his Device Manager has oodles of devices: 5 mice, of 4 different kinds, 3 keyboards of two different kinds, at least a half dozen disk contollers, and on and on. What the hay? I think I'll just jump him the parking lot, send him to the hospital and buy a couple of new machines. I am more stumped than ever and I was pretty well lost before.

by al

I can't figure out to post this at the end of the discussion, so I'll put it here. The machine would not boot from floppy because once it powered down (I am assuming the CPU was popping thermals), it would not boot back up for 10 or 15 minutes. Since it was worth saving I replaced the mainboard (sinec I could not find a 1.3 Athlon anywhere, and the CPU (Duron 1.3 becasue I am too cheap to by faster) and the power supply (since the old one did not have the 12 CPU power tail) and it works like a champ. Everything else was a distrcation, I guess.

by al

Since I rejected the right answer along the way I can't seem to give it points now, sorry. Al

This discussion is closed to new replies.