8 replies
by bouncy64 Accepted solution
by thechas Accepted solution
Hi,
Since these systems had Windows 95 on them, I assume that everything is at least 8 years old.
Swap in a known good power supply, or measure the output voltages with a good meter.
Back in the early days of SDRAM, there were a lot of strange restrictions on many motherboards. If you changed or added RAM, switch back to the original RAM and see what happens. The list of strange restrictions I ran across back then could fill a book. Common limits were 32MB per slot, single density RAM only, and a 16MB limit on all slots when using the third slot.
I assume PCI video cards. There should not be any issues there.
One thing that trips people up from time to time is that some drives have different jumper settings for master with slave and single drive.
The boot sequence you describe is very similar to booting up some drives set as master when they should be set as single.
Chas
by mjd420nova Accepted solution
by now left tr Accepted solution
CPU does not make a 'noise' - thats will be the fan!
Motherboard?
by --loki-- Accepted solution
I had a similar experience recently with an older Gateway machine. the fans came on, lights on front came on... But nothing else, no matter what....
I took EVERYTHING out.. Including the motherboard... and began looking at the motherboard carefully. .... Near one of the serial ports, a tiny component of some sort had been partially scraped off of the board. Power was going through the board, but never getting to the components it needed to, due to this damaged component. It was nearly invisible while it was still in the computer case, but once taken out of the case, it wasn't hard to find.
A clue to this, that made me take everything out like that, was that although the hard disk and the cpu fan was getting power, the heatsink on the cpu and the heatsink for the voltage regulators near it stayed ice cold. they should have begun getting a bit of warmth to them as soon as the system powered on if power was getting to them.
Another clue, was that the lights on the keyboard didn't light up when the system was powered on. So it wasn't simply a video or bios issue... it was never getting that far.
Now on an entirely different system.... It would power up, it would even do simple dos based tasks that were not intensive, including formatting and copying files. but the windows OS would not install or load AT ALL... It would get through the file copying part, which is not cpu intensive, but then when it began configuration, it would instantly reboot, and any attempt to load the OS would cause it to reboot.
Using a boot disk, all the obvious scans were done, with no problems found. A memory burn in test was fine, all the hardware reported in that there were no issues when doing a basic diagnostic.
BUT when a cpu burnin test was done, again, instant reboot.
Sooooooo... initially I tried replacing the processor, with no change in the problem. So I took a closer look at the motherboard with a flashlight. I noticed that a couple of the voltage regulator caps (the cylinder shaped thingys sticking up near the cpu socket) were bulging, and one looked as if the top was leaking rusty colored stuff. Well, that answered that question... lol... without the voltage to the cpu being regulated, it ain't gonna work under any sort of load.
So again, it was a motherboard issue.
But in your case, it seems to me that there's either a faulty power supply, easily tested by simply taking a known good power supply and attaching it to the board and hard disk(dont' even have to actually install it in the case, just to test this)
OR there's a scratch on the motherboard or a damaged component on the motherboard, that's not allowing power to the cpu.
Look for scratching near the cpu fan clips, look for blown voltage regulator caps, look for bits of metal filings near the screws if a screw is stripped, take the motherboard out of the case and attach a powersupply and see if you can get it to boot out of the case, and if so, look for an area that the case might be shorting it... look for any little square thingys knocked loose or missing from the board (for example, if it's obvious that theres supposed to be several in a row, but one is crooked or missing)
That's about all I can think of at the moment... Hope it helps!
by zlitocook Accepted solution
by willcomp Accepted solution
Check capacitors on motherboards for signs of swelling or leakage. Here's what to look for:
by bouncy64 Accepted solution
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending