Discussion Locked

Old Computer

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I've got a computer that just won't turn on. I meane that, the computer comes on but, the monitor won't do anything. Although I did notice that the light on the monitor will turn green once on but, when I hook up it up to the back of the computer the light turns red. What can I do to fix this problem? I have tried to hook up another monitor I have and it too did not come on.

20 replies

by thechas

By the computer comes on, I assume that you meen that the fans spin up.

Do the drives spin up and run their self tests?
If so, the power supply is likely good.

Do you hear any beeps from the speaker?
A single beep usually means that the motherboard has passed it's POST tests.

Do you see hard drive activity that looks like Windows loading?

Start by using a voltmeter to verify that you have 5 and 12 volts DC on the drive power connectors.
If so, the power supply is probably okay.
Check the motherboard, and make sure that the CMOS reset jumper is not set to the reset position.
(This would also be a good time to check the CMOS back-up battery.)

Next, with power off, make sure that the memory, cpu, and plug in cards are fully seated in their sockets.

If the memory is 72 or 30 pin SIMMs, make sure that the plating is the same on both the RAM fingers, and the socket contacts.
If they are different, try cleaning both with a white or pink pencil eraser.

Once you have ruled out the power supply and the motherboard, the next likely suspect is the video card itself.

Chas

by mrrejohnson

I had a similar problem when I recently built a system from scratch.Make sure you check all jumper connections. I had a motherboard manual that was drawn upside down from the reader's perspective.This caused my monitor to stay offline.If you've recently changed any configurations in your PC check them also.Cables come loose.

by morrisonk

If you've already tried another monitor and get the same response, the first thing I would do is replace your video card with a known good one. This is assuming that the CPU is powering up properly.
If this doesn't solve your problem, then furthertroublshooting will be required to ensure the CPU is indeed powering up and successfully completing its POST.

by pocono

Make sure you're video card is properly seated, the cables are secure, and if not, you might be in the market for a new video card...Peace

by pinoy_teknik

There is one or more peripherals that are malfunctioning, or not properly configured and inserted to designated slots.... to know that follows Chas answer and you will find it.

This is common problems that we encountered and Chas have steps in this situation...So, make some safety measures while proceeding...

Pinoy_Teknik

by pinoy_teknik

Oh......im sorry in repeating this answer this is an acciddent, coz while im clicking Submit my Answer the browser takes blank, then im going to hit back, on and on, after it is subitted properly.....

IM SO, SORRY....

Pinoy_Teknik

by pinoy_teknik

There is one or more peripherals that are malfunctioning, or not properly configured and inserted to designated slots.... to know that follows Chas answer and you will find it.

This is common problems that we encountered and Chas have steps in this situation...So, make some safety measures while proceeding...

Pinoy_Teknik

by pinoy_teknik

There is one or more peripherals that are malfunctioning, or not properly configured and inserted to designated slots.... to know that follows Chas answer and you will find it.

This is common problems that we encountered and Chas have steps in this situation...So, make some safety measures while proceeding...

Pinoy_Teknik

by pinoy_teknik

There is one or more peripherals that are malfunctioning, or not properly configured and inserted to designated slots.... to know that follows Chas answer and you will find it.

This is common problems that we encountered and Chas have steps in this situation...So, make some safety measures while proceeding...

Pinoy_Teknik

by pinoy_teknik

There is one or more peripherals that are malfunctioning, or not properly configured and inserted to designated slots.... to know that follows Chas answer and you will find it.

This is common problems that we encountered and Chas have steps in this situation...So, make some safety measures while proceeding...

Pinoy_Teknik

This discussion is closed to new replies.