Discussion Locked

PC will not power up

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
My son's PC is (was) an Azza M/B with a K6-2 500 proc. Last week it would not power on. Popped open the case & checked the power--had no 5v standby. Bought/installed a new P.S. Still would not power on, but the new one had standby voltage. Checked out new P.S. in another computer--worked fine. Checked out old P.S. in another computer. It was fried. Bought a new motherboard (Amptron with 650 T-Bird). STILL will not power on. Unhooked everything(CD,Hard Drive, Floppy, case fan, speaker,LED's, pulled Sound Card & NIC). STILL will not power on. Here is my question. The only things common to the two configurations are the RAM (1-128 DIMM) and my video card (Rage Fury Pro), so one of those must be causing the problem. SHOULD my PCbe able to power up with no RAM installed? SHOULD it be able to power up without a video card installed? I think I read somewhere that if you try to power up without RAM or video card, you get warning beeps, but the fans still spin, and the light comes on (nothing happens on this PC). I do not want to throw any more parts (or money) at this problem without being pretty sure of a fix. All help is appreciated.

7 replies

by cdobbin

If you are getting no fan or light activity at all take the main board out of the case and connect the power supply to it, you will have to short the pins that send the signal to the power supply(to turn on)so take note of where the power switch is connected to. Something could be shorting out the main board to the case. I recently experienced a problem where my PC would not power on, when I removed the power supply from the case and tried it, it worked, put it back in the case and it would'nt power up again, once more set it on the floor(pwr sup) and it would power up. Set the power supply in the case with no screws and it powered up, put the screws in it and it still powered up so I was happy. I asked people about this and they told me something could have been shorting with the case.
Good luck with your problem.

by tranman

This is a standard ATX form M/B with standoffs that match the holes in the board. I have pulled the M/B and looked under it for loose screws; etc. Also laid a piece of newspaper in the box and put the M/B on that to isolate it from the case--no help. Sorry.
Paul

by pstark

Before you removed the hard drive, could you hear the system reading from the drive at boot-up? If you have a bad video card, it is possible that the machine is booting with no video.

If you do not hear the beeps at power-on (POST), then your memory is probably not the problem. Since it sounds like you have another system that works, you might be able to test (if the memory is the same kind) it in the other machine. Alternatively, you can remove all but the minimum and see what, if any differnce, that makes. (Consider using only one stick, and switching it out for another if it doesn't work. You may have one bad one, but probably not two...)

You may also be able to pull the video card from the other machine and test it in this one.

Of course, you always have the monitor to consider as well. You may want to make sure it works on another machine. It is possible to have problems because of bent pins in the connector, or simply no picture...

Good luck. (I'll be curious as to any new info based on your efforts...)

Paul.

by tranman

The machine does not power on at all--fans do not spin, power light does not light up, disks do not spin--nothing happens at all. I do have standby voltage. I am very hesitant to swap components to a working machine because something in the old configuration *seems* to have fried both the motherboard and the power supply. Sorry.
Paul

by dcosgrove

If you power on the board with just a processor you should get ram beeps, if you have an internal speaker. These are usually 1 long beep repeated over and over. If you then put the ram in, you should get vga beeps. Usually 1 long and two short beeps but this varies in some boards. In both cases the power supply and processor fans should spin. Dont be suprised if it's just the switch though, leave the board installed and find which two pins are for the power swithch. Should be a diagram inthe manual for the board. short those two pins and see what happens. I have also seen bad or stuck reset buttons burn out a power supply so check that too. Most people can do without a reset button if thats the problem, just dont plug it back in.

by tranman

That was what I needed. I was unsure if powering up without any memory was OK, and if so, what indication I might get when I did it. After reading all of the warnings about not running the power supply without a load, I was paranoid. I pulled theRAM, and the box powered up--fans spin and the power on light lights, and I got the "RAM beeps" that you described--one long repeated eternally. Obviously something on the DIMM is preventing the power supply from coming up...I can deal with that. BTW, good thinking about the switch, but I had already disconnected it, and shorted the contacts with a screwdriver to test for that problem. Thank you for the good info.
Paul

This discussion is closed to new replies.