Discussion Locked

Performance

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I want to find out what I can do to improve the performance of my home pc?
I've got a PIII 650 MHz, 128 MB RAM on GA m/board, 30GB HDD, running Win 98.
But unbelievably, it is not quick at all!
Bootup is slow and apps take an age to open. What can I do??

7 replies

by dmiles

Difficult to say what can be done if anything at all.How are you determining the performance to be slow?
Do a maintenance on your system by runinng it from Programs-Accesories-System Tools,the other thing todo is type in MSCONFIG in the run commandand see what applications are loading at startup.You may also try running a third party software to bencmark the system to get optimal performance.

by bryanmorison

Thanx; did maintenance - no noticeable improvement.
msconfig was useful - found plenty of applications loading at startup, removed some of those.
haven't tried 3rd party benchmark software yet.

by dcosgrove

There are a huge amount of variables in just the items you metioned, not including software which is the big one. A non OEM version of windows, not one provided by, say, packard bell, will run much faster as it has not creepy little programs to runon start up. You can help by removing thigs through msconfig. There are also different speed H/Ds. They are rated in rpm and the type of bus, ata66 for example. Memory also comes in speeds, most notably bus speed, pc66 pc100 and pc133 all reflect the clock speed they are meant to run at. Try removing as many programs from start up as possible, also multi media keyboards and such take more resources than standard 101 key plain old keyboards. decide what you need, remove the rest.

by csmith

This sounds like a hard drive problem. Unfortunately there are many causes for slow data transfer rates from the hard drive. You will have to start with the BIOS.
Under Intergrated Peripherals lines 3 and 7 are most important. PIO of master (line 3) should be auto or 4. Line 7 UDMA master should be auto.
Block mode must also be enabled.
The next thing to check is the hard drive IDE cable. It should be a UDMA66 or UDMA100 cable. The hard drive should be plugged into the end connector, and there should be nothing else on the cable. The CD-ROM should be plugged into a separate cable on the secondary IDE interface. The problem with having the HD and CD-ROM on the same cable is that the auto detection function in this BIOS can screw up and force the HD data rate down to that of the CD-ROM. This is not supposed to happen, but I have seen it.
The UDMA cables have a different appearence from a standard IDE cable. The ripples are smaller on the UDMA66 cable.
If this was an upgrade, was the CD run to install the special UDMA drivers for this board. Do you have the CD?
If all else fails, have you tried Load Optimized Defaults in the BIOS? This selection loads what the BIOS detects is installed. Also check that the HD is set to Master.It will boot as slave, but the boot time will be extended.
That's it for the common hardware problems.
The software problems usually consist of too much stuff being loaded, (Too many programs, too many fonts, etc.) or way too agressive antivirus settings.
Regards, Chris

by bryanmorison

I think you were spot on with the HD idea. I checked the cabling, and sure enough the CD-ROM drive is connected to the HD on IDE-0 (I also have a second HD, 6GB with nothing on it attached to IDE-1)
Originally it was configured as follows;
30GB HD as Primary master with CD-ROM drive attached the as primary slave;
and the 6GB HD as the seconary master.
I have now altered it as follows;
Just moved the CD-ROM drive from IDE-0, to secondary slave, attached to 6GB HD drive still as secondary master.
After I rebooted and changed the BIOS settings there was a remarkable improvement.
Do you think that my new configuration is suitable??
Also, I had Norton System Works loading at startup; I changed the settings to not be "too agressive"Thanx

This discussion is closed to new replies.