Discussion Locked

Prob. w/Gateway Flat Panel Monitor 1500

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I built a computer and all is working great until I boot it up at the customer's house: The video adapter is PowerColor Radeon 9200se, 128 DDR, DVI-I and a vga receptacles. Flat Panel Monitor customer has is a Gateway FPM1500 with what I believe to be a DVI-D Plug. I understand that the DVI-D is compatible with the DVI-I and it fits together fine. Boots and can see display on monitor, can see Windows logo flash, then the green power light on the monitor goes amber and there is no display to be seen; however, Windows 98SE goes ahead and loads - can hear it and also can shut it down with the keyboard even thought I can't see it. I looked at the receptacle on the "old" computer this monitor was plugged into and the receptacle is, I believe a DVI-D, like the plug. This computer was working great with a vga monitor, so it's not making any sense to me. I do not have the monitor driver installed yet, but I don't believe that should make any difference - maybe I'm wrong. Any help would be greatly appreciated - I'm about to pull my hair out with this one!!!!
Thanks in advance
Virginia

14 replies

by vcummings

I am also able to boot into safe mode and can see windows. The settings are 800x600, 16 bit true color (of course, it's 640x480 in safe mode). Also, I'm not sure where to find the driver for this monitor as I'm unable to find much information on the Gateway FPD1500. If anyone can fill in what I'm missing here, I'd be thankful . . . and relieved! It has to be a fairly simple solution and I'm not getting it. Thanks, Virginia

by sgt_shultz

try changing the refresh rate setting on your adapter card but first install monitor driver. i do think the monitor driver will make a difference. your monitor probably fails safe if driven at incompatible refresh rate. if driver 'knows' about monitor's capabilities, you probably will only get configuration choices that your monitor supports. without it maybe you are being allowed to pick an 'illegal' refresh rate. your great experiment in Safe mode supports this theory imho

by vcummings

Poster rated this answer.
Thanks sgt_shultz. I used the monitor driver once I did purchase and install a compatible graphics adapter. I really appreciate your help!

by kennethsf

In some other equipment (not sure about yours) video drivers default to one of the outputs in your card and not both (they treat video hardware as if they were different video cards) so a good try would be to connect a standard VGA monitor along with the dvi-connected unit and then wait for windows to load. Chances are you will get video on the vga unit. Then you can go to advanced video configuration panel (rightclick on the desktop, then choose properties) and look for some tab where you can choose the default video output connector. Choose the DVI output and video should switch from the VGA monitor to the LCD unit. Reboot to be sure.

HTH

Ken

by vcummings

Thank you kennethsf, as your comments helped me to eliminate possible solutions. I did try your suggestions. Poster rated this answer.

by grantsch

I had similar problems with the same monitor. I was using a dual VGA / DVI graphics card and by default windows selected the VGA as primary. If I remember right, I had to boot using VGA monitor, play around with card config make sure the DVI port was configured as primary device. If it's not in the software, there might be a jumper on the card to instruct whether VGA or DVI is primary. Good luck.

by vcummings

Thanks grantsch@eircom.net. This answer also helped me to troubleshoot the problem. Poster rated this answer.

by vcummings

I'm not sure if this is the right place to make this comment, but I didn't want to close the question or not accept any of the answers just yet. I am at a "holding" point on this problem, but have tried installing the monitor driver and that did not resolve the problem, so as a temporary solution I provided a vga monitor until I can resolve the issue with the flat panel monitor. I have spent another 5+ hrs. at the customer's house trying different solutions and none have worked. I will be picking up the computer and the monitor in the next couple of days and will be able to get more in depth with the troubleshooting. At that time, I will try the solutions posted here and get back with all of you. Thanks so much for your answers - I appreciate all of your help!

by kdfdawg

virginia--
i'm having the same issue as you. i just bought a geforce fx 5200 128mb with dual outputs and cannot for the life of me get the Gateway FPD1500 to work. i have had the monitor for a few years and it was working just fine on my old geforce 32mb video card. i would appreciate if any of you have any suggestions- i've tried all the methods described here so far...

thanks in advance

by vcummings

kdfdawg, I didn't see your post until after I had purchased the exact card that you are saying will not work with your fpd1500 monitor. Everything worked fine and was a very easy process, so I'm not sure why your monitor is not working. I sure wish I had an answer for you, but I can tell you that it is not the video adapter card - 5200fx. Sorry! Poster rated this answer.

by vcummings

The only solution I found to this problem was to purchase a Geforce 5200FX 128 MB DDR video graphics adapter. After spending hours reading through the technical specifications of the ATI Radeon 9200se, I found that there is no supported configuration for a single DVI monitor. I uninstalled the ATI drivers using the vga monitor, then removed the ATI card and replaced with the Geforce card, booted with only the Gateway FPD 1500 monitor and let Windows install the standard graphics adapter. Then I installed the Geforce drivers, then the monitor driver and all is fine now. DVI monitor is working fine and system is "purring". Sure wish I had done this little switch in the 1st place!!! I guess, though, it was worth it as long as I learned something from the problem, and I surely did!!! Thanks for all your help!!!

This discussion is closed to new replies.