Discussion Locked

Problem with Video card, HELP!!!!!!

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I purchased a PNY AGP GeForce 64MB video card. I disabled
the on board video, and uninstalled the drivers in device manager. I switched
the jumpers and installed my new AGP video card. It booted up with video, and I
installed the drivers. Initially, before I rebooted, I went to display
properties and tried to switch the resolution. At this point I moved the slide 1
notch to the right, and hit ok. My video went off and the light on my monitor
went amber. I rebooted by holding the power button in(since I couldn't see a
thing) It booted with video now and hit F8, booted into safe mode. It wouldn't
let me move my settings back, the changes wouldn't apply. So I removed the card
from device manager and tried again. Rebooted, then installed the drivers again
from the cd. I then restarted for changes to take effect. I had video until it
was about to put my icons up(and the resolution
looked pretty high) when the video went out again. I then rebooted again, hit
F8, and enabled VGA. This put me at lowest setting again. I tried the
performance test from Norton and ran a 3D test. It said "no 3d adapter
available". I did these steps a few different times in different sequences, same
result. I also tried switching the monitor refresh rate, which again, made me
lose video. I went on the Intel site and it said my chipset(440) is no longer
supported. My monitor drivers are current. Is this product plain and simple not
going to work ever, or what? Can itnot handle a 64MB video card? I got this PC 4 years ago in May. Please get
back to me ASAP. Thanks

13 replies

by dmiles

From your description it does seem as though you have 4X support for this video card

Iwould check the motherboard web site to find out if it will support this AGP video card

by thechas

Graphics adapters can be tricky to get working.

Start in BIOS settings, and verify that:
a. The AGP card is the first graphics device.
b. The AGP aperture is set to between 64 and 128MB but not more than 1/2 of installed RAM.
c. Any recommended settings per PNY are as specified.

Next, install the Intel INF utility.
http://support.intel.com/support/chipsets/inf/
This will prepare Windows for dealing with the newer graphics card.

Depending on the version of Windows, install the correct version of DirectX (from Microsoft)
For W95, use 7a
For W98 or Me, use 8.X or 9

Now, re-install the driver either from PNY's site, or use the Nvidia 'reference' driver.
Either should be newer than what is on the CD that came with the card.
Finally, verify that your monitor is properly selected / identified.
If your exact make and model is not on the list, download and install the driver from the monitor mfg.

Chas

by gbuck

Check your power supply. Some 3D graphics cards really need a lot of juice. If your power supply is less than 350 to 400 watts maybe this is causing your problem.

by opatzg9

Graphic cards are always a bugger to get going.
Steps are:
1: enable and load motherboard drivers for AGP slot
2:load latest directx
3:load video drivers for new video card
Good Luck!
Keep yourself static free!

by sparky123456

Maybe try removing your monitor from device manager - sounds like the first time you booted up and changed the res it went to an unsupported frequency on your monitor, also did you actually install the drivers and attempt to change res settings before rebooting ? "Initially, before I rebooted, I went to display
properties and tried to switch the resolution" ?

by guruofdos

Firstly, the 440BX chipset boards CANNOT provide enough current at 3.3v for this card! A typical graphics card of the era of your machine maybe had 8Mb or 16Mb of RAM. Ram chips running at the DAC frequencies used by graphics chips pull several amps!!! Double the memory on the card, double the current...quadruple the memory, quadruple the current. It's really that simple!

Secondly, before you change ANY graphics card, don't uninstall the original!!

First, change the drivers to Standard PCI Graphics adapter, then reboot the machine and enjoy a few moments of 640x480x16 colour!!

Then, and only then, uninstall the old drivers.

Third. Shut down and install the new card. When you re-boot, install the new drivers.

This discussion is closed to new replies.