Discussion Locked

QLA2100 FC HBA - can't boot Windows XP.

0 helpful
173 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Im using QLA2100 FC HBA under Windows 2000 Pro - its awesome to have 10,000 rpm 1Gbps drive!
Unfortunatly Windows XP can't boot - setup finishing with error 7B - unknown hardware. When i boot XP from other drive - IDE or SCSI, XP recognize and workwith QLA2100, but i want to use it for more than just fast storage. Qlogic wont supply drivers for XP, and i quess im stuck with W2k. Looking for driver or suggestion. thank you.

173 replies

by jordana

Have you tried using the Win2K drivers?
You have an unusual setup IMHO. I doubt Qlogic will ever supply drivers for XP. You might be the only one who has the $ to try to use Fibre Channel in a Work Station... I am using some QLogic 2100F's in a Win2K AS setup hooked up to a SAN, but would never have thought to try to hook them up to a WS, why bother (Are you running some app that uses disk that intensly)? Plus, my OS is installed on SCSI drives within the server.

That said, have you tried using the Win2K drivers and using the F6 option to specify disk controller during setup? That might work.

Jordan

by mirobg

Unfortunatly you are right - i contacted Qlogis and they wont provide driver for XP thats why im looking here for help. I tryed using W2K drivers already - they wont let WXP boot from QLA 2100FC.
Using this FC drives really help a lot whenworking heavy with Photoshop - i get the work done at least twice faster compared to reg IDE ATA 100 / 7200 RPM.
Thank you very much though.

by the computer wizard

hey

format the drive with win me or 98 make it bootable. you don't have to install win me or 98 then install XP.. you must also make sure you PC BIOS is set to SCSI as the first boot device. and the Qlogic Bios is configured correctly.. and the drive is drive id 0. XP is very particular..

by mirobg

Hello,
Yes, i did this many times. In fact, Windows XP is the only windows - based OS that dont recognize Qlogic QLA2100F FC HBA - i tried all the rest and they work fine with it. Unfortunatly, the problem occur after first portion of Windows XP setup is complete - regardles was it started from DOS prompt, from within Windows 98, ME or 2000 - when it boot with Winodws XP kernel, it dont recognize the controler and return error 7B.

by anomalus

You could use an ide dirve to boot of. You don't need much since the boot files don't take up more then 272 Kb. Then install Xp to the SCSI dirve.
I don't even think that would slow down booting at all.

BTW why WinXP. I don't feel that XP shouldhave been released yet since I've bumped my head against so many bugs I was forced to go back to W2K.
Personally I'm sick of paying good money to be a beta tester for Microsoft.

Hope this was helpful.

by mirobg

I tried this once and it didnt work and i didnt spend much time trying to make it work because i want to skip IDE drive all together.
Thank you.

by craiglins911

yup! Got to love XP;NT drivers are the only ones that may work because its an upgraded W2K almost
XP; I had to use these drivers for my scanner when nothing was availible "works"

by mirobg

Yes, that is what i always try first, but in this case it does not help.
Thank you.

by cdue

This is far fetched, but the commands and technology used under and FC HBA is very similar across the board: Check for the availability for the top-most driver mentioned on this page, its intended for Whistler but the driver model is the same, you have to add it manually. You might have to ask Compaq Support to give it to you, from what I've been told from Compaq: They will support boot on FC

http://www.compaq.com/partners/microsoft/whistler/index.html#rc1

let me know :-)

by mirobg

I download the whole package - about 40MB - just to be sure i dont miss something if i decide to pinpoint FC HBA drivers. Unfortunatly, the Compaq StorageWorks drivers are for Win2000, not .NET, and are not compatable with my QLA 2100F HBA.
Thank you.

by jose mir

Well, let?s see. If the drive works with Win 2000 this mean that is not a motherboard to drive relation problem.
The message maybe is originated between reading the master boot sector and fetching the OS.
Maybe this could sound simple, but, have you used a second box of XP? Anything can happen in Microsoft world.
Another stupid suggestion: Could it be an Active Partition problem? Have you checked it?

Regards,

Jose P Mir
jpm@jpmir.net

by mirobg

I tried to install XP on drive with FAT16, FAT 32 and NTFS without anything else but XP source; tried to install it from IDE drive / bootable CD ROM to non formated FC drive to let the setup format the drive in the way he want. I tried most of this scenario on 3 different motherboards with both INTEL and AMD CPU- no luck so far.

by jose mir

I see, but when you say you tried to install XP from IDE drive and CD-ROM, are you telling me that you have installed the disk as second drive? Remember that having an active partition in one hard drive usually (with just some exceptions) forces other drives in the system (regardless you are installing a new or the same OS) to leave unmarked the partitions as ACTIVE. To be sure you should remove other drives in the system and boot form the CD-ROM.

Regards,

Jose P Mir
jpm@jpmir.net

by mirobg

I had this system set up and running Win 2000 i guess i can make the same with Windows XP - just had to found the right drivers.
Thank you

by maxwell edison

Avoiding Stop Error 7B During Initial Boot of the Runtime:

If your runtime bug checks, or blue screens the first time you boot into it and it errors with bug check code 7B, this indicates that you left out a critical boot device. This boot devicecould include one of the following components: a disk drive, an integrated development environment (IDE) controller, a primary IDE channel, a secondary IDE channel, a PCI bus, or another boot device.

The two most common causes:

You have built the hardware configuration yourself without using the tools to query the target machine for its devices.

You used ta.exe in the bios on the target machine but it returned information that could not be found in the database. This means you couldhave missed a critical device in the configuration process. If you know the specific component or one that is compatible, such as a generic driver that is in the database, try adding one of these components into your configuration and build the runtime again.

(continued...)

by maxwell edison

Try one of the following solutions:

Use tap.exe instead of ta.exe. Using tap can be virtually foolproof and it will determine all devices necessary. You can only run tap from Windows 2000 or Windows XP. Tap will query the registry to identify the correct devices that Windows Setup determined would be best for that machine. Another downside to tap is that it will pull in any devices that it used to install in that machine but were subsequently removed, as well as pull in some software enumerated devices into your configuration that you may not want or need. If this happens, delete the unnecessary component from your configuration.

The second solution would be to examine device manager in a safe build successfully installed on the target machine. For instance, if you already have Windows XP or Windows 2000 installed, open device manager and identify the critical device listed in Device Manager that is missing from your configuration in Target Designer. Then locate the device with the same display name in Target Designer and add it to your configuration.

Source: Andy Allred, Microsoft

http://www.microsoft.com/windows/embedded/community/tips/xp/stoperror7b.asp

REMOVE SPACES from the pasted URL.

Maxwell

by mirobg

My problem is as simple as this - Windows XP don't recognise QLA 2100 FC HBA, hence, can't boot from it and returning error 7B. I know what i have in my machine and i dont need to run anything to find that out.
P.S. The above article is for WindowsXP Embedded, witch is not my case.

by timwalsh

Your problem comes down to this:

There are some sort of generic drivers included with XP that allow you to access the drive as a storage device, but don't provide the ability to recognize the HBA as a boot device.

If the Win2K drivers will notwork, then you need WinXP-specific drivers.

According to the Qlogic website, this particular model has been retired and Qlogic no longer provides ANY technical support for the series - hence your inability to get an XP driver. If the manufacturere doesn't provide a driver, you probably won't find one anywhere else.

The bottom line is either stick with Win2K or be satisfied with using the drive as a fast storage device under XP.

by mirobg

You are right - this is the exact situation. Thank you.
The problem is i don't want to give up and keep trying - you know, the hope dies last :)

by giacomo

Honestly, there isn't much you can do. Perhaps in this case Patience is a virtue. Maybe one day Qlogic will create a driver for Xp. I appologize for telling it like it is. Sometimes beggers can't be choosers. Be happy that it at least works with win2k

Giacomo

by rrgilmore_2001

Maybe you need to edit a driver that partialy works or find someone who knows how to. I know you will reject my comment, but I just thought you would appricate someone thinking outside the BOX. Besides what is rong with win 2k?

by mirobg

Thank you for stopping by.
As far as my knowledge goes i did try to edit the W2k driver that work, but it didnt help, and i dont know anyone who do this. There nothing wrong with 2k - im still using it, but if i could i would like to switch to XP.

by pj

Did you try creating a new project on sourceforge.net?? Maybe if you start a project there to create the driver will be quicker than wait for the manufacturer...
Is not a quick solution but could work.-

Regards.-

Pablo.-

by mirobg

Tnank you, but that site is working with open source projects - no single windows xp driver or article about that.

by nick

I'm not too hot on all this but have experienced similar problems with upgrading ME to XP on some drives, with the problem being a dicsrepancy between NTFS and the HD Controller. The only way I solved it was to format, reinstall 98 (cant't stand ME and on the upgrade, stick with FAT32.

The only other thing I would suggest is doing an install on another drive and using Ghost to copy it across. This has worked for me.

Probably a crap answer, sorry.

by mirobg

Its ok, we all trying to find way to solve our problems - you shared your opinion and experience and i thank you for this.
I tried both NTFS and FAT32 under XP, but it still doesnt work.
Under W2K it work fine with both.

by dualinlinememorymodule

First Thing Is To Flash Your BIOS Ok!

Try Downloading The Drivers For The System XP Approved DST3 Certifided

I Will Contact Microsoft And Ask Them To Contact The Produces And Create Digitally Signed And Bootable System HDD-MB-ROM-RAM Drivers For SCSI IDE Whatever Is Required To Flush The System Into Boot

Try Using The RUN Command Typing MSCONFIG And Configuring URS AND DLL Boot Commands Such As Safe Mode Or Command Prpmt Etc........ BOOT INI

Etc..........

I Really Believe This Is Cause From You Needing A Need BIOS Flash ROM AWDFLASH Update Contact Me On Dualinlinememorymodule@hotmail.com
And I Will Determine Your Motherboard And Get You The Bootable FD And Send Them To You Or Send You The Site As I Dont No Your BIOS v Or MB

by mirobg

BIOS have nothing to do with this because it work just fine under W2k with any of 5 or 6 different configuration i have.

by dualinlinememorymodule

DST3 Is Trying To Overcome Driver Issues In The Near Future And Become A Fully Certified Member Of Microhard And MS Sun Systems We Soon Will Have A Webpage Inovating These Issues And Overcoming Problems With Manufactures ANYWAY!!!!!

Check This Out These Links May Help
If You Reject This I Will Pursue This With You VIA Email Or TechRepublic Ok Goodluck Mate

One Thing Mate Never Buy SCSI Or RAID
Unless Your Using MAC OS Or Linux
So Many People Have Contacted Me About SCSI And RAID Problems Even After BOOT
Use IDE
Goodluck

When Bying Software Pls Make Sure It Is Going To Work With The OS

7B Means= http://search.support.microsoft.com/search/default.aspx?Catalog=LCID%3D1033%26CDID%3DEN-US-KB%26PRODLISTSRC%3DON&Product=&KeywordType=ALL&Titles=false&numDays=&maxResults=25&withinResults=false&Queryl=0x0000007B&Query=0x0000007B&QuerySource=gsfxSearch_Query 0x0000007B

DST3 Links To Try:

http://www.qlogic.com/

http://www.qlogic.com/cgi-bin/ice2-form.pl?KEYWORDS=QLA2100+&Click+to+Search.x=14&Click+to+Search.y=6

http://www.qlogic.com/cgi-bin/ice2-form.pl?KEYWORDS=SCSI&Click+to+Search.x=14&Click+to+Search.y=13

http://www.qlogic.com/support/drivers_software.asp

http://support.microsoft.com/

HBA's Supporthttp://www.qlogic.com/support/product_resources.asp?id=110

Ok Mate Had A Look AT The Site QLogic Have No BIOS XP Ones Sorry But Ya Cant Get XP Ones Yet However You Can Get The 2k Ones Which Means If Ya Dual Boot You Will Be Fine
From Here
And The 2k Ones Sometimes Work With Xp because my modem did

http://www.qlogic.com/support/oem_detail.asp?productid=110&oemid=21

BIOS Flash AWD Should Work Tho!

GOODLUCK DTS3 Technologys My Name Is Walter
I Prefer Being Called Dark Shadow Tho '

Any More Help Im On Messenger
Dualinlinememorymodule@hotmail.com
DST3@arach.net.au

by mirobg

I currently use QLA2100 under win 2K and its ok. When i try to make new instalation with dual boot 2K/XP or upgrade the excisting 2K instalation, it always stop with 7B error.

by dualinlinememorymodule

Solutions In Keys: (EASY TO READ AND DO)

DST3 (DaRk_sHaDoW) Tomorrow's Technological Solutions Today

BIOS Updates (Go To Motherboard Site And Get The Correct BIOS And AWD Flash Format FD And Create Startup Disc And Extract Zip Files To Disc
Boot Via Instructions

Windows Updates

There Are No XP Drivers For Your Device There Are 9x and 2k Linux And Mac Os Only

Configured Boot In Bios

Check JP On Mo Board

Check Jp On Card CCC AGP PCI AMR CNR ... SCSI RAID

Check CPU ALUInstructions

Check ROM Config
RUn : MSCONFIG

x0000000 Dual Boot
2k XP

Goodluck

DST3 tECHNOLOGYS

by dualinlinememorymodule

I Have Been Reading Other Peoples Suggestions Towards Your Solution One Thing Editing Drivers Wont Work As The Driver You Require Is A Pure Dos Driver 8.3 For You ROM It Is Thats Why I Suggested BIOS Updates FLASH IT However The Windows Driver Is Required But Its In Binary C++ So If Ya Got A 5 Year Degree Understanding How To Literally Edit The File And Understanding To Edit The Script To Win2k To Winxp And 1 And 0 Being The Binary Code 0=No 1=Yes
And Changing The Resources In Script Code

Goodluck Buddy

by dualinlinememorymodule

The BIOS Flash You Have To At Least Try This It Is A Solution Because Think About This
The BIOS Flash Date Of THE MB ROM
may not have the parcific sectors detected to determine what it is
Yes it may work with win2k but win2k gathers via ROM
thats how OS work

ROM Direct C++ Programming Direct To ROM BIOS CMOS
Controlling Everything RAM IDE SCSI RAID HB

So Trust Me On This It May Be That The FLASH Bios In ROM
On System Mainboard Requires A FLASH In order to detect the new controller

As windows thinks

it says BIOS Whats this
wheres the driver for this DOS8.3 Or WIN8.3
BIOS RAID SCSI CMOS Checksum
PLS Inform

If 2k Works The FLASH Might Be Only Up To Support The 2k OS And When You Install The XP The Flash Says NEW OS Wheres The Driver NTFS FAT32 SCSI What

I Now What Ya Saying THo

The OS Has Nothing To Do With This VIA FLASH ROM
AWDFLASH
Motherboard Etc...
But Think About This Seriously

Stupid Things Work
Sometimes TOO

YOU DO NO HOW TO FLASH DONT YOU?/

I Do Believe that the computer os you have installed is support with the flash of nt technology however overcoming nt technology into new HD HB NTFS SCSI RAID Etc ......
BIOS Flash is usally required

Hey spoke to a friend that had the same problem from my work today

Called Neil
From Modern PC
He Has A 1500 SCSI 240GB HDD
And he had no xp driver and got error after error after error 7b 50
etc....
thread stuck in cable etc.......
and he flashed and it worked after that

Look
I Do Suggested You Flash

Because Listen To This This Should Influence you

by mirobg

All MB i tryed are flashed to the latest BIOS from ABIT and ASUS - still dont work under XP.

by dualinlinememorymodule

BIOS Flashed Dates As Default With The Motherboard Expire when people issue faults and send them to the manufactures right
and they update it

like you motherboard might not support a new cpu
like my computer support amd athlon but no athlon xp
i had to flash to make it support athlon xp and my support of my mainboard is up to 2.0GHZ
onboard

2k may be supported but xp says hey whats going on her
because 2k is supported by the CD =IDE To there HDD SCSI To There RAM To The BIOS CMOS Check

POST

Trust me i know
windows drivers run via dos to direct to ROm ie THE BIOS so 2k may have the drivers for it or doesnt have problems with it because it doesnt require digitally signed and digitally signed can detect in dos
thats why you get a 7b error
BLUE SCREEN
trust me this is your only solution
im not trying to fuck you around
i am trying to help you out
because i know what its like when ya computer messes with ya mind

So FLASH AND NO CRASH

by bchesmer

From everything I?ve read so far (As of 11-19-02), here?s my best guess at what you could try;
(I know this is not exactly what you want, but it just may give you the desired results)
Get XP going on an IDE drive & have it set as the primary boot device (Set it up as FAT16)
Ghost a copy of the boot device to your FC drive
Keep the IDE drive as the boot drive, edit the ?boot.ini? to boot from the FC drive (To load the OS portion of the boot sequence)
You may have to play around with it but I have done similar things with both NT & 2000 server editions.
Email me at bchesmer@mn.rr.com if you would like to colaborate further about this.

Bryan

by mirobg

I gave it a shot ( actually, way too many..lol ) during the weekend, but couldnt make it work. Thank you.

by todd kimbrell

Sorry, but you will never get this drive going on XP. I have two of them and I have backed out of XP to W2K just to keep using them as primaries.

After repeated contacts to the manufacturer, they will not provide drivers for XP on that model.

I will personally give all my points away on top of yours to the person who actually finds a way to make this drive work on an XP machine.

best regards,

Todd Kimbrell

by wolfbanes

The only thing I can suggest is you could attempt to contact one of the developers of their earlier drivers and see if they have an interest in working on a new driver. The company won't do it, but perhaps you could find a sympathetic ear from a driver author.

by mirobg

How can i contact developers ? All i know is they are made by QLOGIC - and they refused to do drivers for XP.

by bbbest55

The BIOS Flash You Have To At Least Try This It Is A Solution Because Think About This
The BIOS Flash Date Of THE MB ROM
may not have the parcific sectors detected to determine what it is
Yes it may work with win2k but win2k gathers via ROM
thats how OS work

ROM Direct C++ Programming Direct To ROM BIOS CMOS
Controlling Everything RAM IDE SCSI RAID HB

So Trust Me On This It May Be That The FLASH Bios In ROM
On System Mainboard Requires A FLASH In order to detect the new controller

As windows thinks

it says BIOS Whats this
wheres the driver for this DOS8.3 Or WIN8.3
BIOS RAID SCSI CMOS Checksum
PLS Inform

If 2k Works The FLASH Might Be Only Up To Support The 2k OS And When You Install The XP The Flash Says NEW OS Wheres The Driver NTFS FAT32 SCSI What

I Now What Ya Saying THo

The OS Has Nothing To Do With This VIA FLASH ROM
AWDFLASH
Motherboard Etc...
But Think About This Seriously

Stupid Things Work
Sometimes TOO

YOU DO NO HOW TO FLASH DONT YOU?/

I Do Believe that the computer os you have installed is support with the flash of nt technology however overcoming nt technology into new HD HB NTFS SCSI RAID Etc ......
BIOS Flash is usally required

Hey spoke to afriend that had the same problem from my work today

Called Neil
From Modern PC
He Has A 1500 SCSI 240GB HDD
And he had no xp driver and got error after error after error 7b 50
etc....
thread stuck in cable etc.......
and he flashed and it worked after that

Look
I Do Suggested You Flash

Because Listen To This This Should Influence you

by bbbest55

The BIOS Flash You Have To At Least Try This It Is A Solution Because Think About This
The BIOS Flash Date Of THE MB ROM
may not have the parcific sectors detected to determine what it is
Yes it may work with win2k but win2k gathers via ROM
thats how OS work

ROM Direct C++ Programming Direct To ROM BIOS CMOS
Controlling Everything RAM IDE SCSI RAID HB

So Trust Me On This It May Be That The FLASH Bios In ROM
On System Mainboard Requires A FLASH In order to detect the new controller

As windows thinks

it says BIOS Whats this
wheres the driver for this DOS8.3 Or WIN8.3
BIOS RAID SCSI CMOS Checksum
PLS Inform

If 2k Works The FLASH Might Be Only Up To Support The 2k OS And When You Install The XP The Flash Says NEW OS Wheres The Driver NTFS FAT32 SCSI What

I Now What Ya Saying THo

The OS Has Nothing To Do With This VIA FLASH ROM
AWDFLASH
Motherboard Etc...
But Think About This Seriously

Stupid Things Work
Sometimes TOO

YOU DO NO HOW TO FLASH DONT YOU?/

I Do Believe that the computer os you have installed is support with the flash of nt technology however overcoming nt technology into new HD HB NTFS SCSI RAID Etc ......
BIOS Flash is usally required

Hey spoke to afriend that had the same problem from my work today

Called Neil
From Modern PC
He Has A 1500 SCSI 240GB HDD
And he had no xp driver and got error after error after error 7b 50
etc....
thread stuck in cable etc.......
and he flashed and it worked after that

Look
I Do Suggested You Flash

Because Listen To This This Should Influence you

by leehellcat

Ok, looks like this could be a bit of a no go for you, but here's one final crazy idea.
Setup an IDE HDD as your boot drive, if you've got some cash get one that supports ATA133, so that you get 133MB/s transfer rate on that drive, then setup the cache files, pagefiles to reside on the FC drive.
Okay it may not be as gfast as a 1Gb/s tranfer rate, but lets be real, the rest of the PC will slow that rate down dramatically anyway, so will you get that much benefit from booting directly from theFC Drive ??

by mirobg

I did that, but i was not happy with the results and got back to W2K - there is a BIG difference in performance because if you look at it, the HDD is the slowest part of one good 2+ GHz PC. Thank you.

by paulo540

I would suggest selling your Q Logic card setup, then purchasing something along the lines of two 10,000rpm 160MB/sec (1.2Gbit/sec) SCSI Drives and an adaptec 29160 SCSI card (on Ebay for around $140 new). From there you could stripe the two drives and get extremely fast transfer rates. You would need to backup your data periodacally, since if one drive goes out, you're up a creek. I bought some 36GB 10K IBM SCSI drives for $100 a piece and coupled them with my DELL Perc 3 card. Excellent system, superfast.

by mirobg

Well, i guess you are right, but i invested so much for this and dont wont to dump it yet. Beside, who will buy setup that dont work on latest OS - i have to say this in my description, and i dont think anyone would like it..
Thank you

by cg it

After reading at all the rejected answers, [some of the best IT techs around answered your question], and your responses to their suggestions and answers, the only way you'll ever get your Qlogic drive to work is to either create the drivers you need or have someone create them for you. The expense of having someone create them for you outweights just buying new hardware that will work with XP. {Why XP anyway??][I'm not a XP fan at all]. [on average, a good programmer who could make up driversthat will work with XP will cost you about $200.00/hr.] He's not gonna get the tech specs for drivers from Microsoft, make a driver, test it , debug it, retest in 5 hours [$1,000.00]. I doubt if anyone has XP drivers for your drive if the manufacturer never made em nor would anyone go to the trouble of making drivers [as it's just not cost effective to do so].

by cg it

You may have purchased your Qlogic drive in the hopes of 1GB in data transfers from your drive[superfast system]and invested the $$ to do so, but wanting to have the latest and greatest O/S work with discontinued hardware might be asking for to much. If you absolutely positively need 1GB + data transfers from you hard drive to run graphic intenstive programs, then again I ask, why XP? Why any Microsoft O/S. There are $10,000 + systems [more like $30,000] out there for high end graphic design programs that will give all the speed [framerates] needed for that kind of program design[like digital movies].

by mirobg

Thank you for you comments - i know all this and i was just asking if someone ever did something like this. And bellive me, i would gladly accept any solution that work, but nothing so far.
Qlogic discontinued QLA2100 from support with hope big guys will pay big money for 2Gb HBA, but im not one of thouse. So i will use what i already have, and if no drivers for XP or way around pop up, ill stick with W2K.
The reason i tryed to put XP was Clear type fonts, that are only available on XP - i work on 18" LCD monitor and it really looks beter.

by int

hi

There is one possibility i can try

please send me the *.inf and ini file from teh win2k driver setup,

INT

by mirobg

This is not the case - it stop while booting because Windows XP loader do not recognize QLA2100. I dont have a working instalation XP with QLA2100, and when i try to move one from IDE or SCSI drive to FC QLA2100 it always fail.

by mirobg

There are no Win XP drivers for QLA2100 there. I have letter from Qlogic stating that they dont have and do not intend to make Win XP drivers for it.
Thank you

by warbug

I say get your money back and buy a hard drive that will work with xp......if i was paying you by the hour...man......:]

by wino460

are you using the cdrom as your boot device? if so do the install do not hit f6 then Does this thing go all the way thru the install then upon restart present the error or blue screen? if so hit your system power off, (not reboot/reset) master powerthen restart the system, and when the request for boot device comes up hit escape and see what happens. I still have issues getting my Promise raid ata100 installed correctly as it worked in win98se xp calls the driver evian scsi but post an error in task bar that says promise filter driver not found but it is working ya just can't see it in the pam utillity. it is reallt an ide daul channel controller that windows thinks is a raid card wierd huh! I would trade point for a solution as to how toget the driver error out, watch the arrays rebuild and sychronize the way they did in win98se. went to mirroring to save data lose from hdd failure, but the every 6 mo win98se crash got unbearable so I opted for the xp pro with the restore feature. when setting up the qla2100 make sure all ide and scsi that are not required are removed if its an asus board use the onboard ata to load the ide hdd then copy over to the qla2100 remove the onboard ata ide turn off booting for mb in bios for ata andide then restart but hit exc when you get to slect boot device screen.

by mirobg

I used CD-ROM to directly install on empty non partitioned HDD;used pratitined under Win 2K HDD; tryed to upgrade from W2K to XP; tryed to make clean instalation from DOS..all diff ways i gould think of..and every time, so far ...7B

by fenaikh

ote1:
***Very Important NOTE *********
After you copy the URL a space or a %20 maybe gets inserted in the URL when you paste it into your browser. Delete any spaces or such characters from the URL for the page to be loaded.
***Very Important NOTE*********

by fenaikh

Hi

pls read these articles.

1. "do not set the Repartition option to Yes if you need to install a third-party storage controller driver. "

from ...

http://support.microsoft.com/default.aspx?scid=KB;en-us;q307099

2. "MICROSOFT Windows XP
Starting Windows XP will cause a "STOP 0x0000007B INACCESSABLE_BOOT_DEVICE" error if the [SysprepMassStorage] section of the Syspres.ini answer file is missing. [SysprepMassStorage] is a required section and must be present during a Windows XP setup, or the required mass storage devices cannot be loaded. To solve this problem, make sure that the [SysprepMassStorage] is present along side the [Sysprep] section. For more information read Support\Deploy.cab\Deploy.chm on the Windows XP Professional CD-ROM."

from ....

http://www.bugnet.com/analysis/0111/t10xpbugs.html

Good luck

Mohamed

ote1:
***Very Important NOTE *********
After you copy the URL a space or a %20 maybe gets inserted in the URL when you paste it into your browser. Delete any spaces or such characters from the URL for the page to be loaded.
***Very Important NOTE *********

by mirobg

Thank you, but i dont do Unattended Windows XP Setup - not that didnt tryed that too, but ive done it mostly in old fashion way - sitting in front of the monitor, wondering how in to make it work and trying again and again few zillion times..lol

by sgt_shultz

hey, i admire your stubborness/persistence! you go, boy. and good luck to you...
maybe you will become a Windows device driver programmer from this...$80K/year on Monster.com...
Happy Holidays

by fenaikh

Hi

"read Support\Deploy.cab\Deploy.chm on the Windows XP Professional CD-ROM"

"MICROSOFT Windows XP
Starting Windows XP will cause a "STOP 0x0000007B INACCESSABLE_BOOT_DEVICE" error if the [SysprepMassStorage] section of the Syspres.ini answer file is missing. [SysprepMassStorage] is a required section and must be present during a Windows XP setup, or the required mass storage devices cannot be loaded. To solve this problem, make sure that the [SysprepMassStorage] is present along side the [Sysprep] section. For more information read Support\Deploy.cab\Deploy.chm on the Windows XP Professional CD-ROM."

from ....

http://www.bugnet.com/analysis/0111/t10xpbugs.html

Good luck

Mohamed

note1:
***Very Important NOTE *********
After you copy the URL a space or a %20 maybe gets inserted in the URL when you paste it into your browser. Delete any spaces or such characters from the URL for the page to be loaded.
***Very Important NOTE *********

by thamer

Hi,
Qlogic "technical support" discontinue of the QLA2100 products also means they haven't done any testing if a driver of another QLA2xxx product will work with it ... they will not even bother to say so ... if there is.

So,... My 2 points-worth dumb suggestion for thinking that it is a valid one ... goes like this:

Why don't you try installing the XP driver of the QLAxxxxF products specially those having the same describtion as the your QLA2100 product: 64-bit 33 or 66MHz PCI to 1Gb Fibre Channel Adapter, multi-mode optic.

The QLA2200F for instnce!

... (I'm done thinking ... now how do I stop the headache?)

by mirobg

HE-HE, just think a little more and you will accept the headache as something normal.
Unfortunately, i already tried QLA2200 drivers ( for a matter of fact, i tried every driver for QLAXXX i was able to find ) and none of them work.

by frobo

Hi,

i have an other idea for you.
Maybe there is no solution for you under XP, and
you need the fonts from xp. How about .NET Server
Qlogic must develop driver for that OS, and you have the same Fonts and driver for your drive.
It's still aguess, i dont verify that, but try the RC2 from DotNet Server if it will satisfy your needs.

regards

Frobo

by dynamo2003

Goto microsoft.com, check hardware compatibility list for your operating system and if the device is not supportr, contact Microsoft direct or stick with WIN2K professional if it works on it.

by mirobg

WinXP officially support Qlogic QLA2100F - it recognize it, but wont boot from it.
Thank you

by joseph moore

Like most people who have posted answers to your question, I don't think it is gonna work. If Qlogic has no plans on making a XP driver, then I can't believe you will ever get this to work....

Now, that said, I did find 1 very interesting file buried deep in Qlogic's web site. The file is a TXT file called "QLogic Optimizing and Multipath Driver For Windows NT V4.0 and Windows 2000."
The file is here:
http://download.qlogic.com/drivers/4148/readme.txt
(please remove any spaces)

In the OS section of this file, it states the following:
"This release has been tested with Windows NT Version 4.00, with Windows 2000, and with upcoming Beta versions of Windows XP and
Windows.NET. Earlier versions of NT are not supported. This releasedoes not support all Beta releases of Windows XP and .NET. It will support the RTM releases of these products."

Hmmm???

In Hardware Support, it states, "Currently the QLDIRECT.SYS driver only supports the QLA2100, QLA2200, and QLA2300 familiesof Fibre Channel Adapters. It requires the use of the QL2100.SYS, QL2200.SYS, or QL2300 'enhanced' miniport driver
version 7.00.00 or higher found in the \NT subdirectory on the driver diskette."

So, this file is about the drivers for the QLA2100, and it did state that it worked on Beta copies of XP. So, this article is somewhat old (at least a year), but it does give a glimmer of hope.

It talks of doing a clean install of the drivers (including manual removal steps of files and Registry entries that might NOT be done during an uninstall). It also talks of Registry tweaks you can do.

Give this file a shot!
Maybe, and let me stress that, MAYBE this can get the drive to work.

Personally, I would not bet the farm on this one.

Good luck.

by mirobg

I have version 7.5.5.0, 7.5.2.0 and 7.4.4.0, but neither works. The folder that you found the file do not have anything alse but that text file and i couldnt find any other version of the drivers that works.
Thank you

by ___._

I'm sure Dell/Qlogic co-wrote a driver for the QLA2200 FC HBA that was XP compatible:

Dell/Qlogic QLA2200 FC-HBA - (95/'98/ME/2000/NT 4.0/XP/Mac)

You could try using this one.

Try searching for this driver and entering it via the F6 at install for SCSI or RAID Drivers, the S for Additional Device.

Not sure if it will work, but it's worth a try

by ___._

Try the driver for:

Dell/Qlogic QLA2200 FC-HBA

Which works on XP

Worth a try?

by joshwithers

Heres an idea that might work, I've "Slipstreamed" a copy of Windows XP, so that the actual installation CD is Service Packed (SP1). Service Pack 1 updates the whole OS, Drivers the lot. It's fairly easy to Slipstream a windows xp/2k installation, its just a matter of extracting the boot rom, copying the contents to the hdd, running the service pack file with some command line options, and then burning a new bootable cd, with the boot rom u extracted, naming the cd the same, and using the newlyservice packed files.

by mirobg

Sorry it took me a while to try this. I updated the XP installation with SP1 and made a bootable CD, but it still do not recognize my QLA2100, neither it work with the drivers for W2K. Thank you

by techrepublic

It strikes me that there is a simple scsi bios booting issue here.

It is a long time since I have done it so I wont detail the instructions for you, but I would suggest that since you can run the drive and controller happily under XP, you just cant boot from it.

Then create a simple boot floppy, that includes the scsi driver that XP uses once loaded. For NT you needed little else beyond the driver NTLDR and boot.ini, I would suggest that whilst this is not a perfect solution as you would be booting from floppy it is worth a look. Remember that as soon as the scsi driver is loaded the os is going to look where it is told in boot.ini for the rest of boot up, so it should run perfectly normally, just needing a few extra seconds before the boot really kicks in.

Not created a boot disk for XP yet, and off the top of my head I can remember where I read the details, but it should be straight forward.

As another approach, if you see which driver family is used by Linux, then that driver family may well also work for XP (obviously not the linux version).

by ilya

Okay, you said Win2k sees the hard drive. So install Win2k first, then upgrade to Windows XP.

by mirobg

I tryed both clear instalation and upgrade from within W2K, but it do not work. Thank you

by paulo.sedrez

http://download.qlogic.com/drivers/4147/qldirect_80103_w2k_ha.zip

This is the location of the last driver known to work with Windows XP (beta) and QLA2100. Look at the readme.txt, you need some files of a previous version.

If you can't boot with that, you are out of luck - QLA2100 was retired short after the release of these one.

Anyway, you can try some of the setings recommended by HP for its Surestore Disk Array XP. Check at:
http://www.hp.com/cposupport/manual_set/lpg28559.pdf--Sedrez

by jason pilarski

first of all, i recommend that you try and re-install windows xp on the QLA2100. If Qlogic will not supply drivers, than maybe you can find drivers on other sites on the internet, and microsoft also puts out patches and drivers and updates constantly for windows xp. what you might want to do is bring up your problem that you are having, and tell them the kind of driver that you need, and if you can find a large enough group of people who have the same problem, then you might be able to approach microsoft as a group, and ask them for suggestions or even a driver. a petition of a lot of people would possibly help, to prove that it isn't just for you, and there are lots of people suffering from the same problem

by mirobg

I installed Win XP in every possible way - at some time during the installation it have to boot from the QLA2100 FC disk, and without a proper driver XP have no idea how to deal with it. Microsoft list QLA2100 as WinXP compatible, but neveranswered my emails about this problem. Qlogic answered - QLA2100 is not supported anymore and they won't do anything about it.
Thank you.

by vh_s

Interesting ... interesting. Everybody does their share, let me do mine.

1. If it is all about font, why don't you copy over your font to W2K. Should work, right ?

2. I haven't been spending so much time with XP lately. I forgot whether XP has something like W98 SETUP command, that would allow something like using different switches defining different startup parameters. In this case, you might need something like disabling specific XP disk access/parameter, and try the more general, more compatible disk access/parameter.

vh_s

by mirobg

Its not as simple as copy the font - its a different way to present the fonts. And yes - there are setup switches you can use, but they can't solve my problem.
Thank you.