Question Locked

RAID setup

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I bought two hard drives to make a Stripe (RAID0) drive on top of my existing hard drive. I tried all the BIOS options for RAID and all permutations of those options, but always when WinXP SP2 starts loading, the computer restarts. Am I missing something?

Read on for more details:
I bought a Gigabyte 965P DS4 motherboard. Up until now I used one HD and all was well, but now I bought two more hard-drives (exactly same model) and I wish to work with the following configuration:

Drive 1 - SATAII - Un-raided - the HD I used thus far
Drive 2 - SATAII - Raided with Drive 3
Drive 3 - SATAII - Raided with Drive 2
I also have 2 IDE optical drives.

I've created 2 RAID0 (stripe) partitions on drive 2+3 using Intel's Matrix interface. I still wish to run WinXP Pro SP2 from drive 1 which is un-raided. The problem is that WinXP won't load. The splash screen is shown for a second and then the computer restarts.

I suspect one of two options:
1) The BOIS configuration is wrong
2) WinXP needs a driver

If this is a BIOS configuration issue, how should I configure it? I tried all permutations of the following options, but nothing worked. I'm not sure what they mean too:

- SATA RAID/AHCI Mode
> Disabled
> RAID
> AHCI

- SATA Port0-3 Native Mode
> Disabled
> Enabled

- Onbaord SATA/IDE Device
> Enabled
> Disabled

- Onboard SATA/IDE Ctrl Mode
> IDE
> AHCI
> RAID/IDE

I'm not sure if this is relevant, but after the first unsuccessful boot, windows started asking me if it should load in safe mode. I tried it and it asked me if it should load a d347bus driver. It either gets stuck on that, or after it (but doesn't show it loads more drivers)

I've installed all the drivers that came with the motherboard's original CD. One of them was a RAID driver.

So, how should I configure the BIOS? What do the different options mean? Why does windows not load?

Thanks :)

5 replies

by joe-f

If you disconnect the two SATA drives does Windows boot normally? If so, the boot.ini file is probably not correct when the new drives are added. The entries in the boot.ini are relative. If a new controller or drive is recognized by the system the path to the boot files may longer be valid. Here is a Microsoft article about the Boot.Ini: http://support.microsoft.com/?kbid=289022
Sorry, I can't help much with the gruesome details on a SATA RAID. Most of my experience is with SCSI RAID arrays on servers. Since those arrays are hardware supported they exist as usable storage before the OS even loads. No drivers are required. If drivers are needed then the SATA array probably doesn't exist until the OS loads. This means that the array is fine for storing files but won't work as a boot device.

by jonathan.livni

After talking to Gigabyte's phone support in Germany (who where very nice and helpful), I understood the problem, here is the solution:

You can't switch from not working with Intel Matrix Storage Technology to working with it, without re-installing windows. If you switch the controller on (using BOIS \ Integrated Peripherals \ SATA RAID/AHCI Mode) windows won't load (even if all you have connected is one un-raided drive). You can either choose to switch it on and re-install windows, or you can choose to use the secondary RAID controller on board.

If you re-install windows, you have to use the F6 installation (meaning, you need a floppy with the correct RAID driver for the installation so that windows will load and install correctly).

If on the other hand you wish to use the secondary RAID controller, you can do this by changing the following in the BIOS\Integrated Peripherals menu:
Onbaord SATA/IDE Device - switch to Enable
Onboard SATA/IDE Ctrl Mode - switch to RAID

The only menu option I didn't mention is the SATA Port0-3 Native Mode which has nothing to do with RAID, but rather lets you choose if the SATA drives will use native SATA features. I googled a bit about it, and what I figured is that if you have WinXP SP2 (or vista) you can simply turn the native mode on and it should work fine. it does for me.

Anyway, for now I'll keep my un-raided original HD on the normal SATA ports (orange) and connect my two new HDs to the (purple) extended SATA ports and RAID0 (stripe) them. When Vista SP1 will come out, I'll probably upgrade to that, and then I'll probably wipe everything, create a Matrix RAID0 + RAID5 with all 3 HDs, and reinstall windows.

Hope this helped someone :)

by captbilly1eye

I was very curious about what would be the solution and was therefore monitoring your post.
Thanks for the update and all the detailed info!
I too have had good experiences with Gigabyte's phone support.

by jonathan.livni

Aparently my troubles aren't over yet. Quickly I've discovered that my optical drive doesn't work.
In the BIOS Integrated Peripherals menu, if I set Onboard SATA/IDE Ctrl Mode to IDE the optical drive works but the RAID doesn't, when I set it to RAID\IDE, the RAID works but the optical drive doesn't.
I've posted a question for gigabyte on their global technical support site (ggts.gigabyte.com.tw) and I hope they'll have a good answer that will let me run both optical drive and raid drives together. Currently it seems that it's either this or that....

This discussion is closed to new replies.