Discussion Locked

RJ45: wallplate to connector cable

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I now this may be considered basic, but.....

I need to connect a switch to a wallplate - ok, several wallplates :).

My point is:
To have a cat5 cable that has a connector in one end and a wallplate on the other end.

I followed the "A" combination described in the wallplate.
Now my question is.
What is the combination of the RJ45 connector. How can I get it right???

I have tried different cat5 combinations but none seemed to workout. What can I do?????

Can you give me a helpon this?
Or indicate where I can find information regarding this subject.

Thanks in advanced for your time
Henrique Rel?gio
henriquerelogio@netcabo.pt

18 replies

by thechas

In the downloads section here at Tech Republic, you will find several guides to network wireing.

Hopefully, one of them will help you out.

You might also check the website of your hardware vendors for revised wireing guides.

Chas

by brian

I use the B template since that matches the colors on my patch cables. It works fine.

by henriquerelogio

Can you be more specific. I already connected the cable to the wallplate - A template. Now I need do know the color order for the connector

by rawright

Check here: http://www.siriuscomputers.com/rj45.htm

Electrically it doesn't matter whether you use EIA/TIA 568A or B, so long as both ends are identical. I use B for everything only because it was easy to find that format in catalogs when I first started doing networks, but it isn't really important which you use - just be consistent.

by rcom

It would help to know the whole cable run. Computer to wall plate from wall plate to another wall plate then to the switch? From what you describe this may be correct.

Looking at the top of the connector going left to right

brown
brown/whiteorange/white
blue/white
blue
orange
green
green/white

by henriquerelogio

PC connects wallplate (via cable :)), wallplate to connector, connector to switch, switch to hub, hub to pacth rack, patch rack to wallplate, wallplate connects PC. uff :)

I tried the proposed connection and it seems to work. I say it seems, because despite the fact we have 100 Switch and the connection is 100 it just is too slow. Slower than 10. What can cause this. The distance is about 20m maximum (PCs to switch). The connection between Hub and switch is 40m maximum and we used areinforced cable.

by hiraghavendra

For straight connection use the "A" combination on the RJ45 also. And if Cross patch is required use the "B" combination.

by cowen80194

I do install of Telco and Data

The only 2 colors that need to be concerned with at 10/100 is the orange and green pairs.

White is always first.
what you described would look like the following if you are holding the RJ45 with the gold pins facing you (1-8)
1 White Green
2 Green
3 White Orange
4 Blue
5 White Blue
6 Orange
7 White Brown
8 Brown
This would work for a 568A setup
If you swap the Orange and Green Pair as I mentioned above this would be for a 568B setup.
As long as BOTH sides are A - A or B - B that is staright through.
If you use an (A) and a (B) that gives you a cross over cable (Test Cable) good for back to back no Hub/Switch/Router computer connections this also works or is needed to connect simular equipment Hub to Hub for example but most equipment has a button to swap one port for this purpose (usually more expensive units 12 port or more)
Hope this help Email me if you need further information as this is my current profession.
Chris

by wlbowers

You need to get a cat 5 cable tester. Several kinds from $39.95 to $400.00. All of them have a doggle that plugs into the wall jack with a short cable and the tester goes on the other end. Led's or an lcd display tells you the story. Good, Bad, reversed, shorted, open, ect.

TECH Point: There are two types of crimp-on rj45's. Stranded wire takes a connector with the barb or barbs inline. Solid wire takes a connector with the barb or barbs offset to trap the wire.

Since you started with EIA568A here are the specs.

Hold the rj45 crimp-on connector with the release tab down looking into the wire end. As you would be looking at it as you reach to plug it into the wall.

The pins are numbered in this view left to right.

12345678
1 is white / green stripe
2 is green
3 is white / orange stripe
4 is blue
5 is white / blue stripe
6 is orange
7 is white / brown stripe
8 is brown

The only difference between a and b is you reverse the green and orange pairs respectively.

This pair configuration is carried through cable, wallplate, patch cable, to nic or hub.

The problem you are probably having is with the wall plate connector. I have found them to be extremely confusing in their nominclature.

I have had to wire a short patch to them and test until I find the magic combination.

If you need more specifics email me I will be glad to assist.

Good Luck Lee

This discussion is closed to new replies.