Discussion Locked

SMOKE!!!!

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi chaps, this is a machine I was building yesterday, and I am still shaky from the experience...

Pentium 4 2.8c
Gigabyte GA-8KNXP (875P Cnaterwood)
Corsair TwinMX PC3200 2x512MB
Creative Soundlbaster Audigy
Sapphire Radeon 9700 Pro Ultimate3x Maxtor UDMA100/133 (40+60+80 Gb)
1x Zip100 IDE
1x floppy
1x Plextor 24x CD-RW
1x Samsung 16x DVD-ROM
Antec 550 TruePower PSU

After triple checking all connections I fired up the syste, and within 10 seconds there was billowing smoke coming out of the case. The immediately identifiable culprit appears to be the floppy, which 10 min. before was working in the P3 it was cannibalized from. The power cable to the floppy melted, taking out the floppy connector (two middle pin's and plasticmelted only - the two female pins on the cable to the right melted only surprisingly enough), the floppy itself (melteds solders and burned tracks on the PCB) and severely damaging the power cable to the zip100 upstream. I've thrown away both Zip and floppy, but not the DVD attached upstream. That works fine (reads CD's). It looks to me like I might've missed the right-most pin on the floppy when connecting the power cable.

floppy male (melted pins "-")
o o o o +
- -

PSU cable female (melted plastic "-")
o o o o +
- -

Is the PSU safe to use after this shorting or shall I try to RAM it?

Thanks in advance for the help....

7 replies

by sterghios

I need to correct the graph as it dont show up properly...

floppy male ( 0's = melted vs o's OK)
o 0 0 o +

PSU cable ( 0's = melted vs o's OK)

o o 0 0 +

I think I might have missed the 4th pin from the left when I plugged in the cable(would explain the differently melting plastics onthe connectors).

I am all ears! And hit me coz I deserve it...

Sterghios

by dmiles7

Sorry about the misfortune,the power supply can be at checked with a volt meter to see if it is still usable,check the fan area for any burn spots or burn smell with in the unit,you could try testing the unit in another system before chunking it,cannot advise if the supply is bad or good,use your better judgement on this one.

by lju

I did a similar thing... I essentially fried the floppy cable. I think I either plugged the power supply lead in upside down or shifted like you. I didn't actually melt the connector though, I only smoked the data cable. The floppy controller on the board doesn't work anymore but the power supply is in good health. I'm actually still using all the components except the floppy cable and drive (and I'm running with no floppy.)

As far as is your power supply still good or not? I'd suggest getting an ATX power supply tester and testing it before plugging it back in.

by sterghios

Thanks guys. Well Simply.co.uk RMA'd it for cash no questions asked, so I bought another PSU and I am currently going through windows installation....

by timwalsh

You probably picked the correct cause. By misaligning the pins you effectively shorted one of the pins carrying voltage (either 5VDC or 12VDC - from your desription probably the 5VDC pin).

There are a couple things you can do to try to determineif your PS is still salvagable.

Pop the PS from the case and just smell through one of the air vents to see if you smell the distinct odor of burnt electronics.

Buy an ATX power supply tester (usually around $20). This will test the MB powerconnector for any faults. Dig out your multimeter and reconnect your PS to the motherboard and turn it on. Use the multimeter to test voltages on all of the surviving peripheral power connectors. I'm not sure how well the different peripheral circuits are isolated within the PS. Damage to one may or may not effect the others. Obviously ALL the connectors on a single ciruit are toast. If the outputs on the surviving circuits test out correctly, your PS is probably safe to use.

As a lastalternative, open the PS case and look for burnt/melted circuits/components. USE EXTREME CAUTION IN THIS STEP! Dangerous voltages can remain in a PS even after power has been removed! You've already caused damage that would void any warranty, so opening the PS won't further effect the warranty.

Personnaly, I would play it safe and opt for a new PS (or replace it at the first opportunity if it isn't immediately possible to do so).

by dadavis5th

I would replace the power supply unless the rest of the system is not worth the expense. You can get one for $25-$35 if you shop around.
If the system is a cobbled one you don't want to put any money in, I would do the following
1. disconnect the pwer cable
2. test each power connector with an old component you may have laying around
3. tape off the damaged connector
4. Then test in system.
Best Regards,
Alston DAvis

This discussion is closed to new replies.