Discussion Locked

SOYO 6BA+100 & HPT370 Ultra DMA

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently purchased a SOYO 6BA+100 motherboard. When I installed my components in the following manner, and went to explorer, the only drive listed was a C: drive. I had the following components hooked to the following IDE slots
IDE 1 (which supports ATA33)
10.2 GIG hard drive set to master
Iomega Zip drive set to slave

IDE 2 (which supports ATA33)
Memorex DVD set to master
Iomega CDRW set to slave

IDE 3 (which supports ATA66)
Seagate ST320420A ATA 66 20.2 GIG hard drive set to master (formated only)
Maxtor ATA 33 12.4 GIG hard drive set to slave (OS, Windows ME installed)
(I used the 80 pin ribbon cable)

When I booted I set up bios to recognize the hard drive on IDE 1 and saved it. The bios recognized it during boot and recognized the CD's and zip drive. When the HPT 370 searched for devices it found the two hard drives and booted to Windows ME. When I went to explorer, the only thing listed was my 3.5 floppy (A) and the 12.4 gig slaved (C).
Further investigation revealed that the Primary IDE controller had a explaination point my it in device manager.

I took the 20.2 gig hard drive out of the system and made the 12.4 gig a master on IDE 3 and still had the same outcome.

I then moved the 12.4 gig hard drive to IDE 1, the 10.2 gig hard drive and zip drive to IDE 2 and the two CD's to IDE 3. Everything worked fine. I hooked the 20.2 gig hard drive to IDE 1 as a slave and it was detected and showed up in explorer as drive D. But now I have a ATA 66 hard drive connected to a ATA 33 IDE slot and I am not getting the benifits of the higher speed
What do I need to do in order to use the ATA66 hard drive as my OS hard drive on the high speed controller and have it show up in explorer as C: drive? Where do I need to connect the other two ATA33 hard drives to get them to show up as D and E drive.

7 replies

by pschuvie

Not sure how to break this to you but you are trying to put too many devices on the same system. By basic design in a PC IDE is setup for a maximum of 4 devices. 2 on the primary controller (irq 14) and 2 on the secondary controller (irq15). The reason you were seeing the exclamation marks was it is an indication of device conflict and the way you had things set you had contention on the primary controllers.

The addition of a ATA66 controller card is really intended to give you ATA66 capacity by REPLACING the use of the onboard controllers. And most of the cards can handle 4 devices.

So somewhere in the instructions it should have indicated to you that you should go into the system bios and turn OFF the primary and secondary IDE controllers and have that handled by the bios of the card.

The end result would be that you would have the ATA66 hard drive connected as the master on the primary connection on the card, one of the other 5 devices as slave - probably the 12.4 gighard drive. Then on the secondary controller connection of the card -probably the CDRW and the DVD, master and slave respectively. That leaves you 1 harddrive and 1 removable drive to start on a new system and the beginning of your network. Simply put pick the 4 you need the most.

Another alternative would be to put the 2 best hard drives on the ATA primary controller - disable the onboard primary controller - not use the secondary controller of the ATA card - put 2 other devices on the onboard secondary controller.
Same result 4 devices.

I hope this information is of assistance. There are a bunches of folks that wish for more IDE connection points and if simple installing of another card solved the problem the stock on the cardmanufacturer would be rivaling that of CISCO and Microsoft, everyone would want a piece of the action. :)

by pschuvie

You know as I was writting this I was having a tickler in the back of my mind saying "you've seen the card" and the SIIG is the name I could not get to come up.
It could be worth the try, in fact I think I will look at it tommorow myself. :)

by pschuvie

Ok I should have done my homework, dang I hate when I speak before I check. I just read through the specs on that card and it should provide you with the additional connections operating properly as you would want them to. Having not used it I would go back over the instructions very carefully and see if you missed a step, also make sure that you have loaded ANY drivers or such that came with it that should be used. It might be as simple as not having the drivers loaded thus not kicking the card into gear. Sorry about the prior somewhat incorrect information. :)

by lo

Actually, there is a solution that is as easy as adding a card and getting another 4 IDE ports (with all of the headaches and problems one can have with compabibility, addressing, etc.) but better than no solution at all.

I had same / similar and bought a board from Fry's Electronics. It worked on my Win NT and I purchased a similar (same mfg) for my Win 98 sytem. They are $50 or so when I got them. Mfg is SIIG, Inc. 6078 Stewart Ave, Freemont, CA 94538-3152, www.siig.com. BestBuy, CompUSA, etc. most likely carry same similar. My Win NT board is UltraIDE Controller, UltraIDE PRO PCI. It is 2yr or so old I think. The Win98 is newer (but I can't find paperwork). Lo

This discussion is closed to new replies.