3 replies
by zlitocook
What I am going to tell you requires you to open your computer and do things inside. If you do not know what you are doing you could cause more trouble then you have now. If you do not feel ok about doing this take it to a shop.
Ok there is a list of things to try and look at. Try one then reboot and see if it gives you the error, if so try the next.
You need ether the manual that came with the motherboard or be able to go the motherboard maker?s website for jumper settings. The CMOS jumper is what you will be looking for. While you are at their web site look to see if they had problems with capacitors, ether going bad or exploding. It was a problem a few years ago and if it is look closely at your motherboard for bulging or discolored capacitors. The board could be going bad.
Reset the CMOS and reboot it may ask at boot up to hit F1 to continue and accept changes, do so.
Next reseat all components, memory, video card, CPU etc.
Next if you have more then one stick of memory and can remove one, some boards have to have two to work. Remove and reboot. Try the other stick the same way. Do you or dose some one you know have one that works with your board try that.
Clean the inside of the computer, dust and dirt can cause alot of problems.
Has your CPU been over clocked? You may have to look at the CPU to see its speed and see what the computer says it is, there is a way to make a CPU run faster but most of the time it is not wise to do so.
Hope some thing here helps.
by hal 9000
AS well as the above change the CMOS Battery this is a coin sized Lithium Battery on the M'Board and should be a 2030 type[b]Depending on the maker there can be a different prefix or suffix but the numbers should be the same.[/b]
Before you remove the CMOS battery disconnect the mains lead and leave the computer for a couple of minutes to allow the Capacitors to discharge and then remove the Battery and fit a new one with generally the Positive + side outermost you should be able to read the Make and type of the Battery when it's inserted on the M'Board.
Now refit the mains lead and switch on and depending on the type of BIOS used push whatever Key you are prompted to to enter the BIOS Settings and set the Date & Time.
You can also look at the settings on the CPU but don't touch anything yet all you want to do is see if the settings are correct. The first option should be on [b]Auto.[/b] Reboot the computer and when you get up the splash screen press the [b]Pause[/b] button and read what the Specs of the unit are. Unless you have a Company Logo Appear then allow the system to just run on and see if it gives you any form of error message.
If it boots and works properly go into the Control Panel and check the system specs to make sure that the correct speed CPU is being listed as well as the correct amount of Physical RAM. If you have an On Board Video adopter it will steal some of your system RAM so don't be concerned if some appears to be missing what you are looking for here is a big difference to what is actually installed.
by hal 9000
If it doesn't work have a very close look at the Electrolytic Capacitors around the CPU these look like little tin cans standing on their ends and with Plastic covers over the sides if they are bulging or there is any fluid leaking from the base of one or more then they are faulty and you may be eligible for a replacement M'Board for this you'll have to check with either the M'Board maker if the system is a White Box or the maker of the system if it a prebuilt system from places like Dell, HP, Gateway or the like.
If the Capacitors look OK then download the Ultimate Bot CD from
http://www.ultimatebootcd.com/download.html
Make a CD and boot from the CD and run the diagnostics and pay particular attention to the CPU and M'Board tests.
You could also see if there is a newer version of BIOS available for download from the System Makers Web Site or the M'Board Makers Web Site. If this is a prebuilt system always go the the maker but if it's a White Box the M'Board manual will have been supplied with the system and that will give you the Make, Model Number of the M'Board and the Web Site to go to for downloads.
Col
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending