Discussion Locked

Unable to boot

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am just hoping against hope that someone will have a brilliant suggestion for this problem before I have to replace my system board. Here's the scenario. I have a PC Chips motherboard M585LMR v 1.2. I tried upgrading from an AMD K6-2 300 at 66 busspeed to an AMD K6-2 500 at 100 bus speed. The documentation with my board says it supports all AMD K6-2 up to 100, so I figured no problem. Well after installing the new CPU (supposed to plug and play compatible so no jumpers to worry about on the board) the system booted and ran for about 6 days, however, I kept having reset problems with the registry. Registry checker kept giving me the error message "registry checker could not access the registry, replacing with backup...etc." and I could not get my email from my pop3 account, and DNS errors on web pages, although I could connect with my ISP, no problem. After trying to resolve the registry problems for a few days, I finally decided just to reset the CMOS jumper to clear the CMOS memory and start from the beginning. BIG MISTAKE! That'
s when the trouble really began. Now I cannot boot at all. No beeps, no nothing. (I have AWARD bios version 4.51pg dated 5-25-99 which, as far as I can tell has no audio error beeps, except for video), any way I cannot boot up. Power supply appears to be OK. Voltages check out and red light comes on, power fan runs, etc. Any brilliant ideas as to what to do. Is there any other possible answer besides that the motherboard has given up the ghost?Please help if you have any thoughts. Thanks.

10 replies

by dmiles

Is the cpu operating with fan going and no heating problems.
Trouble shoot by looking at the motherboard manual you may have to switch the jumpers the voltage is different and this may be causing the problem.
Make sure that you have compatible memory to match the system bus and memory is not mismatched.
Use a startup disk and boot into the CMOS control panel,in pheripheral configuration of the bios reconfigure to the system setup.
If their is a reset switch on the power supply hit it to reset the power supply,the red light on constantly points to the power supply or a connector is loose,check all connections to insure they are connected properly

by shanghai sam

Maybe I didn't make clear that the mother board does not need any jumpers reset, it is supposed to be plug and play compatible as far as CPU upgrades. All settings are done in the setup program. The 300 and the 500 both run at a core voltage of 2.2 so even if there were jumper options the voltage did not change between the two cpu's. I reinstalled the original 300 at 66FSB CPU. It didn't help. I am unable to get to the set up program, which is the major problem. All the computer does when I turn it on is the power light (green) and the drive light(red) both come on and stay on. The power supply fan runs, the cpu cooling fan runs. That's all that happens. I cannot boot from a floppy, it doesn't get as far as accessing the floppy drive. No video beep (or any beep) and no video comes on. I believe that the computer is unable to complete the POST. The power is putting out the correct voltages into the motherboard, and I just noticed that my second bank of memory was very hot, so I pulled that out as well. The first bank of memory is not hot and is in the primary slot (required bank). Hope that clarifies the problem. Any other ideas?

by sgotero

Hi!, I'sorry to say that if there's no beep, the matter is the processor. If you have the old processor put it again, and try again. It's happend me too with a PIII OEM, without reason, and without beeps, this start and freeze in cmos screen. I change the processor and Ok.

Hope it's helps you.

by donmars

Wow it seems you have a strange hardware situation there! It's not going past post so you cant get to setup.have you tried unplugging the hard drive, floppy drive, cd-rom, remove all boards but the video card or also remove that and use the unboard video. Then see if post completes? If this moves you a step further then add boards back one at a time and restart after each addition. How did you clear cmos? Did you short jumpers with a tool or something? Maybe you damaged the mother board in so doing? Are all the pins on the cpu ok and not bent? Turn the box upside down and shake it make sure you did not accidentally lodge a small screw or metal object where it aint suppose to go! The first step is to get to setup, since you cleared setup itmay have defaulted to user settings for hard drive and other stuff. What happens if you turn it on without cpu installed? do you get entirely different results?

by donmars

Oh and carefully remove and reinsert the BIOS if you can. With all the heat and stress to the motherboard maybe there was some "pin creep", or you could just press on it to seat it better. I prefer a clean reseat.

by dmiles

The problem could exist at the power supply,which could be bad or connection problem,check all connectors to make sure they are connected properly.you may have to try another power supply.

This discussion is closed to new replies.