Question Locked

Upgrading internal toshiba laptop harddrive

0 helpful
67 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

I am considering updating the laptop harddrive in a toshiba laptop. It is 20GB thats in it at present and this is obviously way too small. I have external drives but they are no longer the full solution given the amount of programmes I have installed on the laptop etc

I have changed harddrives in desktop pcs before and have not had a problem, but i have never opened up a laptop before, so I would need some direction on this. Is it difficult? Is there more danger involved that I could damage it?

Also, the laptop came with a 'rescue windows disk', not a proper full windows install disk. I believe this to be because windows is on a partition in the drive or something and this disk helps to access it. Its all a bit of a pain but Im sure one of you guys understands that a bit better than me. This must complicate the process of changing from hardrive to new harddrive?

I want to be able to go through the process of changing it over, and then when finished the laptop will switch on and be exactly the same as before, but with a bigger internal harddrive. So how do i do this? I have heard its possible, but do not know how?

ALL help is very very welcome

Thanks in advance

Best
Jason

67 replies

by wizard-09

Its as just the same as a desktop hard-drive replacment. It's a bit more time consuming but thats all. I would look up the model number and make of your laptop and look at the information to were the hard-drive is placed but apart from that its striaght forward.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome.

by oh smeg

Mainly because of the 20 GIG HDD. This has to be an IDE Drive and these have a Upper Limit in BIOS just like Desktop systems. As 20 GIG Drives are no more and have not been for a very long time the smallest that I can currently buy new is now none they are no longer selling them new. That doesn't mean that you can not find new IDE Drives for a 2.5 inch but they will be Old Stock. You may find a few 80 GIG HDD but these are unlikely to be usable in your system you'll need to find out just how big a HDD you can fit to this unit and remain usable under the BIOS installed.

After that you need a Cloning Utility like Acronis True Image Workstation to clone the Recovery Partition to the new HDD the same size and then clone the remainder of the 20 Gig HDD and chose to use the remaining space on the new HDD. That should work and make things easier for you.

http://www.acronis.com.au/

Col

by healyjason

Could i not just update the BIOS if this is a potential issue regarding the size i can upgrade to?

I will start to look at what size drive my computer model will allow now

by oh smeg

That Upgraded BIOS Files may not be available or extremely limited for such an old system.

Col

by healyjason

When you speak about cloning the partition first and then the rest, how do I do these separately if the new drive is not yet in the computer?

Also, I am probably wrong, but there is hardly any blocks on this type of cloning that will prevent me from doing it, due to it being one that was on it when i bought it, and i imagine the reason is for anti-piracy?

by healyjason

Could you direct me to some info on updating BIOS, and also, how would I go about finding out what types/size of hard drive this BIOS would be compatible with so i can then search for one?

Thanks a lot for your help by the way!

by healyjason

I have read some pages online that have warned of how dangerous it is to update BIOS, and that it should be avoided at all costs

How do you feel about this? I recall doing it a LONG time ago on a computer without problems, but cannot remember in the slightest how i went about it

by thumbsup2

Updating the BIOS is NOT at all something that should be avoided at all costs. It's relatively easy, if you know what you're doing. However, if anything at all goes wrong during the update, one could be left without a computer.

Basically, it all comes down to YOUR level of knowledge and willingness to proceed. If YOU are comfortable doing it, knowing the risks, by all means, proceed. But, if YOU are in the least bit uncomfortable doing it, if you don't know what you're doing, you should take the computer to a professional who you are SURE knows what they are doing. This would mean taking it to a service center which specializes in that manufacturer's products, not the neighborhood kid who 'knows a lot about computers'. If it's a Toshiba, take it to a Toshiba Service Center, a Dell goes to a Dell Service Center, etc...

You still have not told us the make/model of the computer and what Operating System it's running.

by healyjason

Its a toshiba satellite pro A10 running Win XP

I would do the BIOS update myself if necessary, for sure

by oh smeg

It's just if something goes wrong or you continue with the wrong BIOS Update things will get nasty.

As this is a NB I would suggest doing it on Battery Power not Mains Power as you can be sure that there will be no Power Failures if the Battery is OK that is of course. But if you get any warnings that you have the wrong BIOS [b]Do Not[/b] proceed. NB's have their BIOS Chip Soldered onto the M'Board Generally Speaking and this effectively makes it very hard to fix when you mess up unlike a Desktop where you can drop out the old BIOS Chip and drop in a new one.

Now s for cloning the new drive place it into a USB Caddy and leave it there while you perform the Clone. This again is fairly simple but if you are uncomfortable in doing this leave it to a professional and pay them to do it. I once had a customer clone a Blank HDD to their NB's HDD and then wonder why he had no way of starting the NB after that. You can make mistakes but if you look and do not blindly rush in and do as you think needs doing instead of reading the options it is fairly easy.

When you have finished fit the Old HDD to the USB Caddy and use it as a Backup Device so that when the NB fails you have a working solid Backup of your Data. It's a lot cheaper than needing to take the HDD to a Data Recovery House to get the data recovered. I spent 56K once for a 40 GIG HDD to get it recovered but it was a rush job and needed to be done immediately. So it was a bit more expensive than if I had of left it for a week or two.

Col

by healyjason

Probably a silly question on my part, but i am guessing that a usb caddy and a usb hard drive enclosure are the same thing?

I do not have either, so i imagine the suggestion is that i buy one along with a new hard drive? I would be willing to do this if its necessary, as long as its not too expensive, and there is not a simpler method?

by peconet tietokoneet

So we can find out if there any bios updates and the in's and out's of your model.
If you can give that then we will be able to assist further.

I have a few Toshiba model manuals on my server, if i have the same as your model i will be able to assist you better.

by healyjason

I dont have access to that laptop right now but will later

A quick thought though, It is a laptop and the floppy disk drive is separate, attachable by USB. Will this affect the method of flashing the BIOS?

by thumbsup2

If the laptop is new enough, it should have an option in the BIOS which can be turned on so it will boot to a USB device.

If it's an older laptop, that option may not be available.

by thumbsup2

The document I found (dated 2004) listed a 40GB HDD standard and the launch page you found (dated 2003) said it had a 30GB HDD. Since the HDD the OP says they want to replace is only a 20GB HDD, I figured it was either older than the document I found, or it had been whittled down when it was ordered to save a few bucks. ;)

Do you remember if, back then, they were capable of booting to a USB device, namely a USB floppy? I can't remember that far back! :(

by older mycroft

So never really delved very deep into 'em.

Both my Rock Xtremes (both stolen!) were born in the Spring of 2004, and they couldn't boot from USB, although they DID have internal floppies along with internal DVD+-RW drives.

I really couldn't say whether the Tosh is USB bootable or not.

by oh smeg

The USB option wasn't available in 2003 on anything but maybe the Top of the Range NB's of the day. Even then they would have had to be the newest model available which this one obviously isn't.

Col

by healyjason

surely theres a better way to find out if its bootable from a usb floppy than memory??

by healyjason

Not a spring chicken but a good laptop nonetheless and one that ill hang onto if i can get a bigger HD and more RAM in

I dont believe in buying entire computers new if a part here and there will suffice for the time being. Hence my wish to upgrade if possible, without buying new

by oh smeg

HDD in while you clone from to, it.

As you have a NB here there isn't an option of fitting it internally so you need some other way to do this. :)

Col

by rob miners

I would be inserting the new hard drive and restoring from the Recovery DVD/CD. A lot less of a hassle and you arn't bringing the garbage with you.

Think of it as a new lease of life for the Operating System and the Notebook. You can easily reinstall your favourite programs and recover Data from the old drive through the USB enclosure.

by thumbsup2

.. after all, IF there is a recovery CD (I can't remember if they said there is one or not), why worry about what's on the old HDD. Just put the new HDD in and use the recovery CD to get the system up and running clean.

by rob miners

Also, the laptop came with a 'rescue windows disk', not a proper full windows install disk. :D

Considering the age of the Notebook that is what I would be doing. I like to have a fresh install every now and then. It clears the cobwebs in the registry. ;)

by healyjason

are you guys familiar with what exactly is on these recovery disks, and also what would be on the partition on the hard drive? Im not certain but if there was a way for me to check i will?

by healyjason

Im probably wrong, but given the fact that i believe the windows and other stuff to be stored on a partition on the current drive, wont inserting a new drive and then trying to boot from the recovery disk be a bit pointless if it then tries to locate the windows files and cannot due to them being on the hard drive that i have removed?

I could be wrong but its just a thought?

Im not totally against the idea of a fresh windows install but do not see it as a necessity so would be very reluctant. Also, i am not the only user of this machine so would prefer to avoid the hassle of explaining the reasons to the other user and then trying to go through the process of ensuring all 'needed' files are copied before changeover

by oh smeg

Made specifically for the Hardware that it was supplied with. So if you have the Recovery Disc that came with this NB new it is exactly the same as what is on the Recovery Partition.

The only difference is that the one on the HDD is faster to install than the one on a CD as the Read Times of a HDD are faster than a CD.

Col

by thumbsup2

... and they suspect there is a recovery partition on the original drive which would be used in conjunction with the recovery CD.

If this is true, all they need to do is use the HDD manufacturer's software to clone the entire original drive, boot up to the new drive to make sure it works, THEN use the recovery CD to set it all back to factory condition.

Sometimes, we overlook the obviously simple steps. :D

by healyjason

Good idea on trying it first on the new drive before touching the existing one, but still i must come back to the point that i would probably prefer to copy the existing drive onto the new drive 'as is' so that when i boot from it for the first time it will be the exact same PC as it was but for the increased disk space

I am sure this is a straightforward process given that I will be using a brand new separate drive and will get an enclosure for it, but my main concern is whether or not the partition complicates things?

Basically i want to copy the existing drive EXACTLY onto the new one, to save all the transfering of files and setup of all programmes etc, mainly due to it not being just me who uses it

by healyjason

By OP do you mean 'Opening Post'?

You say that i need to just use the manufacturers software to clone the original drive, do you mean clone it TO the new drive when its plugged in via a USB enclosure?

Why then would i need the recovery CD, if it is going to be the same contents when i insert it into the laptop? Also, reverting the drive, new one or old one, back to factory condition is something i wish to avoid, as it creates unnecessary hassle of reinstalling stuff and copying files

What do you think?

by thumbsup2

Based on what you've told us and what we've found when we were doing research for you, I highly doubt the laptop is new enough to have the option to boot from a USB device.

There's one way to tell for sure though. Go into the BIOS and look for an option to allow booting from a USB device.

.

by healyjason

In response to the post by thumbsup2, i could not reply directly due to it saying 'You have reached your maximum message level.'

So i added my reply here

How do i go about entering the BIOS to see if it has the boot from USB floppy device feature?

Thanks for your help

by healyjason

Regarding the caddy, what should i do? If an external drive casing for a notebook harddrive is not what i need, what is?

by oh smeg

While the Yanks do have a adapter that will allow you to plug in most HDD's Types I'm pretty sure that it's not available in Ireland yet or the UK

http://www.cooldrives.com/saandidehadr1.html

You need to look for something like this which should be freely available and far more useful to you as well.

http://www.mittoni.com.au/usb-20-25-hard-drive-enclosure-p-1221.html

If you where to get the first option here it's only useful for testing and direct reading not for Backup Use. Actually none of these devices are suitable for Full Time Use as they allow the HDD to get too hot, but provided that you only use the HDD when you need it there is no problems.

The USB to HDD Adapter doesn't adequately protect the HDD from Bumps and Vibrational Damage which the HDD is subject when in use.

Col

by healyjason

So i need a HDD enclosure for a 2.5 inch with IDE interface?

What type of drive? I have read about ata-5 amongst many others but am unsure

I recall it being easier when buying a sata drive but i may be wrong

what do i need to look out for?

Is there a maximum gb level that my laptop will take?

by healyjason

So how do i get 'into' the BIOS to check or turn on this?

Thanks

by healyjason

This is as much info as i can see on it

TOSHIBA Satellite Pro A10 PSA15E-01PJY-EN
System Serial Number: Y3621515G

by healyjason

There must be a simple way to find out if it is. If so how?

by healyjason

again, memory is maybe not a totally reliable source here. is there a simple way i can find this out??

by rob miners

should have the same contents as the Recovery Partition that is on the Hard drive. The easiest way to do this would be to install the new Hard drive and boot from your Recovery CD/DVD and install a fresh copy of the Operating System.

You can then connect your old Drive to the USB caddy and take ownership of the files on the old Drive and copy them to the new Drive.

by oh smeg

That is always the easy way when you have the unit at hand.

To open the BIOS look at the Toshiba Splash Screen and press the Button listed on it. This is generally either Delete, F2 or F10 but it is listed when the Toshiba Logo Appears just after you press the Power On Button. When you have the BIOS Setup Screen showing navigate tot he Boot Order and see if there is an option to Boot from a USB Device.

However I'm sure that you'll find that this unit doesn't support Booting from USB.

Col

by healyjason

in reply to OH Smeg

I went into the BIOS and the options for booting from are HDD, FDD, CD-ROM, LAN

It has FDD, but nothing about USB. The Fdd is only attached via usb so i am guessing that this FDD option is more or less redundant and unhelpful in this instance?

by healyjason

Although, below that 'Boot priority' option there is a 'HDD Priority' option which has currently got 'Built-in HDD->PC Card' selected in it.....changing this value would hardly help at all in our case?

by oh smeg

It may boot from the USB but it may also require a Floppy Drive to be present and be the only thing it will boot from.

What does the Owners Manual say here?

Col

by healyjason

...the partition and the CD or DVD will contain EXACTLY the same thing? This is a toshiba, if thats any help?

So, if i was aiming for a clean factory install on the new drive it would literally be a matter of sticking in the new drive to the laptop in replacement of the old one, booting from the cd and then id be back to the factory settings but with a larger hard drive?

But, again i must say, i wish to avoid this. I am interested in putting in a new drive that will have ALL of what the old drive currently has, AS IS, but with the greater storage?

by oh smeg

If you where to fit a new HDD and use the Recovery Disc you wouldn't have a Recovery Partition on the HDD or the ability to reload the system and destroy your Data by using a Key Combination at the POST Screen.

But otherwise it would be the same.

Col

by healyjason

So is it possible to do it in such a way that the new drive would have these features?

Also, any ideas on how to make an exact copy of the computer as it is now onto a larger drive?... bearing in mind the partition etc

by oh smeg

You can not fit a SATA or any other type of HDD as the Connection is different and they will not work in that Drive Bay.

However you need to but either a IDE or PATA Drive these are the same thing but are called different names depending on the maker.

As this is a NB you can not exceed the Upper Size of a HDD that the BIOS Supports and you need to keep a careful eye on the amount of Electricity that is required to power the HDD. It wouldn't be a very cleaver idea to fit a HDD that required 2 Amps to replace one that only required 750 Milliamps s it would be unlikely to work for vary long if it worked at all.

Col

by healyjason

So i need an IDE or PATA?

How do i find out what size my BIOS will take?

How do i find out about the electricity like you said?

by oh smeg

Look in the Manual under Upgrades or Replacement Parts that will be a good starting point. Failing that look at the Makers Web Site for what Replacement Parts they sell for this model.

As for the the Power Requirements look at the Sticker on the HDD. This has all the information about the Drive printed on it. It covers the size, The other things like Product Number and so on as well as the Voltage Requirements.

As for Updating the BIOS it is only any use if it fixes problems that you are encountering or allows you to fit a larger HDD.

For Instance a newer BIOS may allow you to fit a 100 GIG Drive instead of a 80 GIG HDD and it may allow booting from a USB Device. :)

Col

by oh smeg

And clone Both Partitions to the new drive. Either Ghost or Acronis can do this but both are Pay for utilities.

Some of the Free ones may work but I have no experience with them. You may even be able to use a Cloning Utility from the HDD Maker s well.

Col

by healyjason

Its not conclusive on the issue but i will go ahead a try it and get back to you

by healyjason

So to clone the drive, i just insert the new HDD into a caddy or enclosure, plug that into the USB port and then use one of the cloning softwares?

And, this will make an EXACT copy of the drive as is? Including the exact same partition?

And then i replace the one in the laptop with this new one and its as easy as that?

by oh smeg

Cloning Utilities only clone 1 Partition at a time and the First one gets copied to the Root of the HDD. Here you need to confirm what is actually on the HDD by looking at it in DOS Mode so when you get the DOS Prompt Type in [b]FDISK[/b] and press Enter. At the prompt change to the HDD and see what Partitions are listed. There should be at least 2 it not 3. The Primary Partition which you know of as the C Drive is the majority of the HDD there may be a smaller FAT32 Partition of any size depending on the what the maker has placed on it and that is the recovery Partition. There will be a Small Area of Unallocated Space this holds the Partition Data as well as a Drive Map generally around 8 MEG or so but depending on the Partition Type FAT or NTFS it can vary in size. When yopu know this restart the computer [b]Do Not[/b] try to do anything from this point as you will destroy Data.

If there is a FAT32 Partition that is relatively small you clone this one first and then clone the Large Partition to the remainder of the space on the HDD so you can use the option to [b]Use All Available Space[/b] on the HDD when you clone the NTFS Partition. Well at least it should be a NTFS Partition for XP here but some old systems retained a FAT32 File System Format for XP which wastes a lot of space on larger HDD so you are better off converting it to a NTFS Partition. Read the following which is from the XP Help Section

[i] Choosing between NTFS, FAT, and FAT32 You can choose between three file systems for disk partitions on a computer running Windows XP: NTFS, FAT, and FAT32. Use the information below to compare the file systems.

NTFS is the recommended file system for the following reasons:

NTFS is more powerful than FAT or FAT32, and includes features required for hosting Active Directory as well as other important security features. You can use features such as Active Directory and domain-based security only by choosing NTFS as your file system.
It is easy to convert partitions to NTFS. The Setup program makes conversion easy, whether your partitions used FAT, FAT32, or the older version of NTFS. This kind of conversion keeps your files intact (unlike formatting a partition). If you do not need to keep your files intact and you have a FAT or FAT32 partition, it is recommended that you format the partition with NTFS rather than convert from FAT or FAT32. Formatting a partition erases all data on the partition and allows you to start with a clean drive.
Whether a partition is formatted with NTFS or converted using the convert command, NTFS is the better choice of file system. For more information about Convert.exe, after completing Setup, click Start, click Run, type cmd, and then press ENTER. In the command window, type help convert and then press ENTER.

In order to maintain access control on files and folders and support limited accounts, you must use NTFS. If you use FAT32, all users will have access to all files on your hard drive, regardless of their account type (administrator, limited, or standard.)
NTFS is the file system that works best with large disks. (The next best file system for large disks is FAT32.)
There is one situation in which you might want to choose FAT or FAT32 as your file system. If it is necessary to have a computer that will sometimes run an earlier version of Windows and other times run Windows XP, you will need to have a FAT or FAT32 partition as the primary (or startup) partition on the hard disk. Most earlier versions of Windows cannot access a partition if it uses the latest version of NTFS. The two exceptions are Windows 2000 and Windows NT 4.0 with Service Pack 4 or later. Windows NT 4.0 with Service Pack 4 or later has access to partitions with the latest version of NTFS, but with some limitations: It cannot access files that have been stored using NTFS features that did not exist when Windows NT 4.0 was released.

For anything other than a situation with multiple operating systems, however, the recommended file system is NTFS.

Important

Once you convert a drive or partition to NTFS, you cannot simply convert it back to FAT or FAT32. You will need to reformat the drive or partition which will erase all data including programs and personal files on the partition.
The following table describes the compatibility of each file system with various operating systems.

NTFS FAT FAT32
A computer running Windows XP or Windows 2000 can access files on an NTFS partition. A computer running Windows NT 4.0 with Service Pack 4 or later might be able to access some files. Other operating systems allow no access. Access is available through MS-DOS, all versions of Windows, Windows NT, Windows 2000, Windows XP, and OS/2. Access is available only through Windows 95 OSR2, Windows 98, Windows Millennium Edition, Windows 2000, and Windows XP.

The following table compares disk and file sizes possible with each file system.

NTFS FAT FAT32
Recommended minimum volume size is approximately 10 megabytes (MB).
Volumes much larger than 2 terabytes (TB) are possible.

Cannot be used on floppy disks.
Volumes from floppy disk size up to 4 gigabytes (GB).
Does not support domains.
Volumes from 512 MB to 2 TB.
In Windows XP, you can format a FAT32 volume up to 32 GB only.

Does not support domains.

File size limited only by size of volume. Maximum file size is 2 GB. Maximum file size is 4 GB.

Note

Some older programs may not run on an NTFS volume, so you should research the current requirements for your software before converting.[/i]

Col

by healyjason

.....i think! I went into BIOS setup and changed boot priority to boot from FDD. Then restarted with the USB Floppy attached with a blank floppy in it and it tried to boot from it

It couldnt so it say something to the effect of.... 'Remove disk or media. Press any key to restart'

So what now?

Also.......what is the benefit of updating the BIOS?

by oh smeg

You need to make a Boot Disc. Use a Blank Floppy and open My Computer.

Right Click on the Floppy Drive with the Blank Floppy in it and chose Format from the Drop Down List. When the Next Window opens add a Tick to the Box that has the option to [b]Create a M$ Dos Start Up Disc.[/b] After the Floppy is formatted restart the computer with the Floppy in the Drive and see if you get the DOS Prompt that should look something like this

[b]A:>[/b]

At that point you have a Bootable Disc to work with and are good to go.

Col

This discussion is closed to new replies.