Question Locked

USB Keyboard & Mouse stop working as soon as Vista Welcome screen appears

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm working on a friend's computer. When the vista welcome screen appears, the lights to the usb keyboard and mouse turn off and I can't log in.

I can only get into the bios setup. Safe mode does not work. And the desktop (Dell Studio 540) does not have PS/2 ports.

I've tried booting from install disk and running repair. Also, ran system restore from recovery tool without luck.

If I leave the PC at the Welcome screen, after a while the screen saver comes on. So I'm not sure if the computer has gone into a power saving mode. Not that it matters - without a mouse or keyboard I can't get anywhere!

Does anyone know the resolution to this problem?

When I plug in a SATA XP drive, the mouse and keboard load without problems.

I've backed up the computer but since she has so many specialized programs, I was holding back on a complete system restore.

14 replies

by jdclyde

did you try a different port?

did you try a different keyboard/mouse?

how long has this been this way? Was it all at once that it went?

is this a ps2 keyboard/mouse with a usb adapter?

have you connected the keyboard/mouse to a different computer to verify they are still working?

try installing another keyboard/mouse after Vista is up, to see if it will recognize and install the new hardware.

by mpalermo

I've tried all of the above (different port, unplugged, different usb mouse/keyboard, etc.) but still no luck.

They are usb (no ps2 adapters).

This happened a week ago. I think it has something to do with power/sleep settings but as I cannot get into Vista, I can't make any changes.

by bizintelligence

USB works with XP then it is not internal hardware issue. It seems to be a problem with Vista then. Something like system drivers.

You have said "safe mode does not work". So what do you mean by that? It doesnt go in safe mode at all?

Have you tried connecting keyboard only i.e. just keyboard on separate USB ports?
Try that and let us know.

Can you try remotely enter into computer (you should have IP address of computer) via remote desktop connection?

Cheers !

by mpalermo

Yes - since it works in XP, it's a Vista issue. Since she has all specialized settings, I didn't want to have to restore.

No keyboard/mouse in safe mode.

Yes, I've tried keyboard only. Mouse only. Still doesn't work.

I have tried to remote to this PC. I can work on that. I'm not sure if remote desktop is turned on. This computer is not part of a domain.

Thanks!

by peconet tietokoneet

Go into the BIOS and look under the USB section and make sure that "Legacy" is Enabled.
Or you can use this tool here:
Re-install your USB drivers with DevCon Command Line Utility...
http://preview.tinyurl.com/nunpjz

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks

by mpalermo

I've checked the bios but there isn't a legacy option under USB.

I will check out the command line utility.

by rob miners

settings are correct it maybe a corrupt Driver Cache. If you can externally load XP and access the Vista inf folder you can back it up and then remove these files. Reboot Vista and it should autodetect and recreate them. Follow the steps in the Batch file.

How to fix Vista driver cache

http://pmhesse.blogspot.com/2007/07/how-to-fix-vista-driver-cache.html

Edit: to add
Make sure that Plug & Play is enabled in the BIOS.

by bizintelligence

If above step fails then can you please try putting vista HDD in other machine to see if it works there or not.

Also,do you have spare PCI USB 2.0 Controller? If yes, try that....

If is most probably a corrupt vista system driver.

Cheers !

Share Knowledge to Increase Knowledge

by mpalermo

I intalled a pci usb card but it didn't change anything. I haven't put the hard drive in another computer because I don't have any other pc's with sata drives.

by rob miners

Basically all you have to do when you boot from the XP CD is create a directory for a Backup and move the files. At the command prompt type in these commands and press Enter.

mkdir c:\windows\inf\infback

move /y C:\windows\inf\*.* C:\windows\inf\infback

Once you have finished restart the System and see if Vista will detect the Keyboard and Mouse.

Something similar to this solved an XP problem not so long ago.

Edit: change the drive letter c: to the drive letter that represents the Vista boot drive.

by mpalermo

After making the above changes, I rebooted the system and it went into Windows repair. After the repair it went right back to the Welcome screen (with mouse and keyboard lights off and still not working).

Thanks anyway.

by seanferd

If you do, you can check the ACPI registry settings on a known working system with the same configuration, then fix the bad registry from the console by editing or importing.

by rob miners

reset CMOS and see what happens but if XP is working it really seems like Vista has lost the plot.
Have you tried booting without the mouse and keyboard attached and at the welcome screen attach them.

This discussion is closed to new replies.