Discussion Locked

W2k Pro - motherboard upgrade questions

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,

I'm trying to get some preliminary info and opinions about upgrading one of my systems. It's an ASUS/PII-300/256MB with all the standard devices running W2k Pro. Runs great but it's slow. I'd like to upgrade to an Athlon 750 and have to change the motherboard to do it. My question is, how do I get W2k to detect the new moboard and load the correct drivers? I've already hooked up the new 750 mobo temporarily and W2k just gives the blue STOP screen of death. I booted to the W2k Pro CD and attempted all the repair options with no luck. Also tried reloading W2k and it craps out telling me my hard drive is corrupt. Some history: this system was originally running W98SE and was upgraded about four months ago to W2k Pro. All went well except for a couple of drivers I had to find and load. Since then it's been running fine but slow. The Athlon 750 mobo is one that I'd been using in another system with no problems. I'm primarily a hardware guy and don't pretend to know much about W2k. The majority of my customers still use Win98SE so that's what I know. But, it seems to me that there should be a way to upgrade a motherboard without having to reformat and reload W2k(never had problems doing this with Win9x). I've checked out the MS website/knowledgebase for any info about what I'm trying to do but found nothing. Any suggestions would be greatly appreciated.

Thanx,
Jack

23 replies

by stans

There may not be an answer to this question. I have found myself needing to stock more than one type of motherbord depending on whether you are doing an upgrade or full install. I have found a few motherboards on the market that work fine for the price, will not work correctly when you upgrade, but work fine with a full install. it sounds like you found one.

by mindwave1

if you can reinstall your old MB and get it to boot, delete ALL MD related devices and THEN only boot to safemode on 2k, allow 2k to reinstall the drivers. this HSOULD work, (per my mcse instructor) however in ral life i have never been able to do anything but an FFR (fdisk, format, reinstall), when you did the upgrade did you convert to ntfs?

by montea7

Go to the Recovery Console...type listsvc....you will see a list of services and drivers that Win2k will attempt to load. Locate your IDE drivers and type disable drivername, this will disable the driver and should allow Win2k to boot with a defaultIDE driver.

by cvjack

This sounds good. Thanx. I'm wondering though, why is W2k too stupid to see that the IDE controller has changed? Seems like any really smart O/S should notice the change and load the default driver all on it's own.

by cvjack

This sounds good. Thanx. I'm wondering though, why is W2k too stupid to see that the IDE controller has changed? Seems like any really smart O/S should notice the change and load the default driver all on it's own.

by cvjack

This sounds good. Thanx. I'm wondering though, why is W2k too stupid to see that the IDE controller has changed? Seems like any really smart O/S should notice the change and load the default driver all on it's own.

by shanghai sam

RE: "It's an ASUS/PII-300/256MB with all the standard devices running W2k Pro..."

All previous recommendations based on clean install of Win2K are probably the best solutions for your situation when replacing a mobo. And clean install is also Microsoft's recommendation for such kind of upgrade. Your system would be clean from all kind of problems accumulated from previous installations.
And there's a good chance that you save much time with clean install in comparison with sort of disasterrecovery after swapping the motherboards. Just backup all your data
(including useful documents, downloads, preferences, address book, etc.) first. Have all your installation CDs and drivers handy, and that’s it.

I see you have a Slot1 mobo. If it were one of i440BX models, a Celeron 1100 (128 K CL2 cache) on a FCPGA-to-Slot1 adapter board might be a better upgrade. If Asus’s site confirms Coppermine support.

Otherwise, nobody could guarantee that installation of your harddisk onto a completely different platform, as Athlon, would be successful on Win2K.

by nickmkhn

RE: "...never had problems doing this with Win9x"

Yes, it's a snap with a Win9x: always works this way.
But NT with its Hardware Abstruction Layer is a completely different story.

This discussion is closed to new replies.