Discussion Locked

W2K "Trap 00000005"

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Your assistance is needed urgently.

I finished defragging a Compaq laptop (W2K Pro) with Norton Systemworks 2003, then downloaded mail and surfed a bit before shutting down the machine. All was fine.

The next morning on bootup I got am immediate black screen with the message "Trap 00000005 Exception" followed by several lines of hex. Now the machine won't operate beyond that point.

I can't get to the W2K boot screens. Compaq diagnostics doesn't show any problems. The Recovery Console doesn't repair anything, but sees my disk volume. However, Norton won't scan for viruses via the CD because it doesn't seem to be able to access the HD. I replaced the RAM sticks and removed all cables, etc.

I just get Trap 00000005 and Trap00000006 error messages. I CANNOT even get into Safe Mode.

None of my usual tech sources even mention these "Tech" errors and neither do the MS or MS TechNet knowledge bases.

Any suggestions on What went wrong and How to fix it without reinstalling the O/S.

18 replies

by cg it

Question, When you first turn on the power, to you see the Compaq logo? or the POST screen? (sounds like a virus problem that has corrupted the BIOS if you don't see a Logo or POST screen at poer on) [I doubt Norton Systemworks was the culprit]. Next Question, can you get into the BIOS after power on? If the BIOS/CMOS table was corrupted there isn't much you can do except replace it via the manufacturer.

by cg it

If it is a BIOS/CMOS problem you won't lose your data on your hard drive. If you can get into the BIOS after power on, there is a possible soution to get Norton Antivirus to work, what you have to do is change the "boot from" sequence in the BIOS toCD Rom first. Once that is accomplished insert the Norton CD and power down. Then power back up. The computer will boot from the CD in lieu of the hard drive [though from what you describe in you question you've tried that].

by cg it

Another thought, is the laptop a new Compaq model or an older model. Some manufacturers, like Compag added their own little code in the BIOS and Master Boot Records (older type of machines). A manufacturing ploy to get service repair $$ by getting you to take your computer into a Compaq repair facility should you have any problems with your machine. Only by having their diagnostic discs could you get in and fix whatever the problem was.

by cg it

To really be able to diagnosis a problem like this is watch the BIOS initalization sequence via a POST card [service tech stuff] and find out where in that sequence the problem is. The BIOS initalization sequence goes something like this, power on, chipset initialization, memory detection, BIOS to Ram, Keyboard, VGA BIOS, processor initialization, system clock, VGA interface, BIOS logon, memory test, IRQ assignment, hard drive controller, floppy controller, boot attempt, operating system boot attempt. Since you see something on your screen you've at least gotten to the VGA interface initialization. The next step is BIOS logon where you press either the delete key or some designated F key to enter the BIOS for setup or do nothing and continue. These startup processes are usually hidden by a logo screen and either you press the TAB key to see the POST screen or just see the Logo screen. Please provide a little more detail on what you see [though new DDR memory/ 2.0 Ghz processor machines do this so fast sometimes you don't even see the logo screen. To compensate for fast BIOS initialization, press some F key like F2 or F6 or the Delete key immediately after you power on your computer [sorry but it's trial and error here until you find the right keyboard key to enter the BIOS).

by cg it

[continued] if you can get into your BIOS, then it's not corrupted to this point in the start up sequence. The next step is memory test and since you replaced the memory, doesn't seem like that is the problem. Next after that is IRQ assignment and if the BIOS doesn't detect the different resource interfaces and assign an IRQ to that resource your computer will not run past this point. That could possibly be your problem. This indicated that a). that portion of your BIOS code is corrupted or your mother somehow went bad. {partial corruption of the BIOS isn't likey]. If the problem isn't there then it's in the next steps floppy drive controller and hard drive controller. Again these are BIOS initialization and they detect that these componets are connected to the mainboard. Problems here can be as simple as a disconnected power or data cable or a data cable improperly installed. After that, is when the BIOS basically turns over control of the pc to the operating system via the Master Boot Record contained on the hard drive. This is where most viruses that are destructive to a pc try to attack. Corruption of the MBR virtually leaves a PC unusuable until it's fix and can cause the symptons you in part describe.

by cg it

As that article said. It definately is a hard drive problem in the Boot Sector. Repairs to the Boot sector of the hard drive can be accomplished provided there isn't a physical problem. Looks to be a virus of some sort.

by cg it

Since this other persona who has a similar problem was able to boot from a CD, you can boot to your Norton systemworks CD and run a virus scan of the boot sector and see if it can repair it. If Norton Antivirus does detect a virus, I suggest you send it to them for Anaylsis ...

by jimmy

Step 1 - Try to isolate the true cause of the problem.

Place the (Possible faulty) Hard-disk in another PC you know works. Does it boot now?
If NOT please say and well try to resolve the issue with the faulty disk without losing any of your data.
You say you are using Win2k but was the install done using FAT32 or NTFS?

by grj2000

UPDATE from GRJ2000:
Still no luck. I swapped the W2K NTFS drive with a W95 drive and the laptop booted. I reinstalled the original W2K NTFS drive and now receive a TRAP 0000000D General Protection EXCEPTION message. I could not installthe NTFS drive (wouldn't fit) in the spare laptop, so we'll try it w/ another machine. Clarification: previously tried Norton Systemworks 2002 from the CD but it would not scan the HDD. Then used W2K Pro Recovery Console, which said it saw W2K in the operating system folder.

by rcom

Whoa! I had the same errors on my compaq laptop and found an article directly relatled to trap 00000006 on compaq's site. I typed in "trap 00000005 exception error" as a search.

http://communities.compaq.com/

The advice was to run setup and select "R" (repair) as the type of installation. It worked fine. I didn't lose any of my data or programs.

The bad news. Later I started getting other and eventually pre OS errors and the system finally failed. What had happened was the AMD 700 CPU burned up. It was still under warranty so I took it back to Comp-USA. After the tech damaged the replacement MB they gave me a Toshiba laptop which has more power larger screen and XP home. Even though I know better I didn't backup my hard drive, so I lost everything.
But because of the newer system I got over that.

If the unit is still under warranty take it back. But back up your data first. Most tech's at places like this will repartition and format the drive as an easy way out.

To get a backup, you can get an adapter that allows you to install your laptop hard drive into a regular PC, then you can copy/ghost the drive.

The adpater and install hardware can be purchased at the following link. It's only about $30.00 retail.

http://iec.net/dsk9015.html

This discussion is closed to new replies.