Discussion Locked

Water Seep's into a P'C'S,Laser Printers

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
There has been water seepage into my pc and laser color printer, i have been able to get the equipment to work after through cleaning and drying. I want to know what are the chances of the Equipments failing due to water seepage in near furture, say6 months down the line. Is there any technical data sheet available for these kinds of failures or is it just pure luck, as to how much time it would take to fail or it wont fail at all.

12 replies

by popeye_doyle

If your PC & Peripheral are working fine, then on this occassion you're lucky. Water Damage is quite efficient at Making a PC into an oversized paperweight. So it is unlikely that your system will have any probs related to the spillage.

by thechas

Generally, problems from water damage show up right away. The damage tends to be permanent if the system is powered up with wet components.

The question is, where did the water get to?
And, how pure the water was?
Most of the cleaning performedat the plants that manufactured the components in your PC and printer was done with "pure" water.

As long as the water was not too dirty, and did not get into any circuit boards, drives, or certian mechanical parts, you should be fine.

The only way to check where the water got to, is to open up the cases, and look for evidence of the waters path.

If it looks like the water did got onto any circuit boards, I would clean the affected areas with a spray electronics cleaner. Allowing the spray to run off the nearest edge of the board.
(use proper ESD precautions when handling the boards)

As to the drives, if the water just got on the top of the drive, I wouldn't worry any, unless it looks like a vent hole was drenched. In that case, for safety's sake, I would backup the data, and replace the hard drive.
(It would be a good idea to perform frequent backups for the next few months.)

The printer is a little more complicated. My recomendation would be to have it cleaned at an authorized repair center.
If the water got onto the rubber rollers, or in the gear train, it would be best to have a proper clean and lube performed to assure that the printer will not fail prematurely.

Chas

by shiny_topadm

Hi, just to add (from the repair shop's point of view): The biggest factor seems to be how 'clean' was the water? If it was mostly just plain water, there will be minimal damage from anything left behind when the last bits of water evaporate. If however, there was sugar, salts or other minerals left behind, these can accelerate corrosion which will damage some components over time. We have seen this from "beverage spills" or flood damage and it makes the future reliablity doubtful. If, on the other hand, the water was mostly pure, you should be okay...

good luck

by deokule

Thanx for the replies..To clarify on certain points raised by u, i will tell u how the water seeped in. there was lot of water on the top floor above my computer center, and the seepage started on friday night and it was discovered only on monday morning. the water might be contaminated with cement form the celeing

by otl

One thing missed is that if the circuit board or components has a residue (normally white with cement, salt or clorine) then over heating could cause a problem. If components appear to be clean and free of residue you may not have equipment problemsfor the normal life of the equipment.

Very lucky that nothing shorted out, good indication that no critical components had water damage.

by wlbowers

Any equipment that was on at the time could
have started conductive corrosion. this will
look like green foam around the leads of the
chips and circuits. The water will have
chemicals from the sheetrock, insulation (if it
was cellouse) andany thing else it washed
through as it seeped in to your computer
room. These chemicals will affect the
components in varous ways unless they are
cleaned and neturalized. This can be a
sudden death or wierd phantoms problems
that creep in over time.

I warn customers involved in disaster recovery
that equipment that works after a situtation like
this might last a day or it might last years. If
this equipment is used in a business then you
better maintain a constant backup.

Good Luck Lee

This discussion is closed to new replies.