Question Locked

Western Digital external Hard drive

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I bought a Western Digital hard drive (the model number is something like wxc806076780). It was working fine untill last week Now, when I plug it in I get a "Safely Remove Hardware" message, but the drive does not appear in My Computer and I cannot access it. I've tried uninstalling the driver and then re-connecting it; Windows appears to detect it (launches the
'Found New Hardware' popup) but it still does not appear. I tried this on another computer and the same problem happened.I did all the troubleshooting steps, it find every thing ok.
I used the same cable and same USB port to connect my camera that works fine. So, I dont know if it is my hard drive or some thing else. My computer has Windows XP

Thanks
Asgar

5 replies

by Former member

Have a look in your "device manager",
Start > settings > control panel > system > device manager, in here look for "disk drives", there might be a red or yellow tag, right click on this and select "delete", then reboot. Make sure that your external hdd is NOT CONNECTED, when re-booted re-connect your hdd and it should be business as usual.

Please post back if you have anymore problems or questions.

by oh smeg

And see if the Drive is listed here. Left click to highlight the drive and look to see if there is an active Partition on it.

If there isn't you have been removing the Drive without using the Safely Remove Option and the Partition Tables have been corrupted.

What you do from here depends on what was on the drive. If it isn't important or you have the data elsewhere just right click on the Drive and in the Drop Down Menu chose the Format Option and format up the Drive. When this is finished it will again appear in My Computer/Explorer and will be accessible as required.

If you have Important Data on the Drive that you don't have copies of you'll need to implement some Data Recovery Software to either recover your Data or Rebuild the Drive Partition Tables. What happens here depends on what Software you use to recover your Data.

If you opt for the cheaper option of Recovery your Data you'll need to save all the output to a different drive to prevent the possibility of Overwriting other Data on that HDD and making it harder or impossible to recover.

For a short list of some Data Recovery Software look here but this is by no means a complete list.

http://tinyurl.com/273ay5

http://tinyurl.com/rmvrv

http://tinyurl.com/yvrsl

http://tinyurl.com/yyk8cm

http://tinyurl.com/382vm

http://tinyurl.com/ynwnel

http://tinyurl.com/nc4kx

http://tinyurl.com/2wox7l

http://tinyurl.com/374d8b

http://tinyurl.com/djw6u

http://tinyurl.com/f73se

http://tinyurl.com/8bd3f

http://tinyurl.com/afu2j

While the last 2 are from the same company they are very different products. Win Hex should only be considered foe use by someone who knows Hex Inside Out while Davory is a great cheap General Purpose Application.

Personally I prefer the On Track Option but it's anything but cheap. However because I use this type of software a lot it's paid for itself many times over by now, for a cheaper option Spin Rite from Gibson Research or Stella have both very good reputations by other TR members.

Col

by mezyounus

Thanks for your reply, I don't see any yellow tag under disk drives.

by yourweldguru

I find that PC Inspector File Recovery (freeware) is the simplest. You just (reportedly) can't or shouldn't run it from the drive you're diagnosing, ie; the drive you want to recover files from. You can install PCI on your EHD, and pc, just don't run the exe that's on the drive you're need stuff recovered from.

PCI may squalk once in awhile about a missing file and/or lock up once in awhile, but using task manager to exit PCI, then if it balks again (after you use task mgr to exit PCI), just re-boot the pc and use PCI again.

Those few tips always allow me to re-access files and/or a drive that balks at listing or showing files I know are there.

It seems PCI is many times only capable of continuosly copy-pasting just those files in any single given folder (exacerbating, but the darned thing simply works and its free).

I have the most luck only using PCI's
"Recover Deleted File" tab (even though I
never, myself, deleted any files).

Added tip is when at PCI's 'select drive' window, my needed files are I think always in '..disk #*' folder. Highlight it and click the green arrrow.

Also, some one to half dozen or so fould files may/will list w/their file names being corrupted usually by one letter or symbol. As such, those files won't 'save as' to any location, so simply rename them.

Why such a simple set of tips isn't afforded, I guess is because its freeware.

This discussion is closed to new replies.