Discussion Locked

What is a "Slim" IDE interface?

0 helpful
63 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently purchased a DVD-ROM drive (Matsushita SR-8185-C) that was advertised as having an IDE/ATAPI interface, but when I received it, the connector was NOT the standard 40-pin...instead, it is a densely packed 50-pin connector that is only about7/8 inch wide. Also, there is no power connector on this drive, so presumably the power is supplied through this same connector. I've been told that this is a "Slim" IDE, but I can't seem to get any more details about it. Can anyone tell me about this? Is this some kind of new standard? And how can I use this with my existing controller, or do I have to get a new controller? If so, what kind?

Thanks!

63 replies

by mckaytech

Hmm... I can't find any information anywhere on this drive, but the connector sounds like a high-density SCSI connector but that wouldn't supply power.

It's certainly not a "standard" but I would guess the cable is proprietary but the interface is not.

paul

by grbeckmeyer

I found this product that sounds like a frame/removeable drive system, but no specs on it.
http://au.store.yahoo.com/estore-au/9032.html

I also found some info at HP and Toshiba that look like proprietary drives. The HP drive fits into a Vectradesktop and connects to a riser card.

Your drive is probably intended for a specific brand/model PC, or they just sent you the wrong drive. I was not able to find any info on that model number to check the specs.

by Former member

It sounds like a SCSI-2 connector to me.

by sgeorgiades

No, this is definitely NOT a SCSI-2 connector...too small. This is about half the size of a SCSI-2.

by 1stladytech

The Slim IDE interface is the standard developed for laptop use. Some of the Desktops are starting to use this interface as it requires less power connectors, and probably less power for the drive (can't confirm that). The cable supplies both power and interface, but you can usually get a adapter kit for installing a laptop hdd into a desktop. Not sure if it would use the same cable set, but should have one available for the cd rom set as well. Good luck,

Vickie

by mark.thomson

I tried entering the following into www.google.com ("slim cd" and bay) and found what may be relevant products from www.cidesign.com or www.servercase.com (the 1st 3 hits). Slim CD drives also seem to be used a lot in 1U rack mounted servers.

I suspect that the reason for slim CDs having more pins than 2.5in HDDs is to accomodate the direct audio connection

by steve moores

The slim IDE interface is being used in many small form factor pc's IE INB's netvista A400
and Compaq's deskpro EN SFF, also their rack servers also use these devices.
You are correct in that the bus supplies all of the power.
i have a special cable (purchased in the uk) to allow you to install one of these evices in a desktop pc, this then plugs into any standard IDE IDC connector(PIO mode 4 ot UDMA etc)this has a fly lead off to a standard power connection.
warning although it will connect a 2.5" HDD I've been unsuccessfull in connection drives larger than 6Gb. CD's & DVD drives work fine.
drop me a mail and I'll send yo the lead !
regards steve

by joshg

Take it back and get the right drive for the job. You'll save yourself alot of headaches!

by rrapson

Found this answer - might work:
Micro Solutions Inc. 212 604-0884 voice, 212 604-0784
fax. $15.00 + $5.00 shipping last September.

by kevinsaucier

Alright, I am taking a stab in the dark as my laptop experience is not what it should be. But, is it possible that this is a Laptop version of a SCSI 2 connector? I found a product made by Adaptec called a SlimSCSI board. It may be possible that whoever told you this is a Slim IDE is incorrect or lying. It's pretty odd to have a computer connector (even a new one) and not be able to get one hit on it's name when searching Yahoo. You may try searing the IEEE website (standards.ieee.org) andsee if you can find an answer there. Beware, they want you to subscribe.

Good luck.

BTW, here is address of the Adaptec product:
http://www.adaptec.com/worldwide/product/proddetail.html?prodkey=APA-1460D&cat=%2fTechnology%2fSCSI%2fSCSI+for+Laptops

by sgeorgiades

No, this is definitely NOT a SCSI unit. Answers 4, 5 and 7 above seem to be on the right track. Thanks, anyway!

by damon_edwards

These drives are often used in the Dell Latitude series and require an "adapter cage" to allow the interface to work. Power is also powered throught this adapter.

by vitoga

The 50 pin slimline IDE connector is used on mobile CD's and DVD's. These drives take up less room to allow for even smaller chassis designs. I believe 50 pin ide is used in embedded PC's, micro PC's, notebooks and on 2.5" hard drives. I noticed some motherboards that I found for 50 pin ide hard drives support 486 and Pentium processors making the 50 pin ide an old (in computer years) technology.
Cellcomputing.com (http://www.cellcomputing.com/third/support/prodguide/generic/c2i-cbr-ide-4044s.htm) has a cable for 50 pin ide HD's but they are for 50 pin IDE headers.
Cellcomputing also has motherboards for the 50 pin ide including the Half Size board (http://www.cellcomputing.com/third/snglbrd.html#ATPCMCIA)and a CardPC Development Board(http://www.cellcomputing.com/third/evaltool.htm)
and on it's Plug-N-Run line (http://www.cellcomputing.com/third/prodnetindex.html)
I know Intel used a 50-pin (mobile) slim ide header on retired motherboards D810EMO and MO810EMO.
A 50-pin slimline to 40 pin (convential)IDE converter can be found at baber.com(http://www.baber.com/baber/products/slimline_cd_adapter.htm).

by vitoga

This is ridiculous. Now there's one between the . and htm. Last try. This is embarrassing.
http://www.baber.com/baber/products/slimline_cd_adapter.htm
(I checked it this time)

This convertor is not just a 50 to 40 pin convertor but it also hasthe power connector and the audio connector coming from the cable. Since power and audio is provided in a slimline 50 pin connector and not in a 40 pin connector.

by vitoga

By the way both power and audio is provided through the 50 pin slimline IDE connector.

by raymondkn

Well the space is being added after posting!

I also made sure it wasn't in there, but now I look dumb :D

OH well!! the link is good! just remove the space. "..ter.[space]htm"

by dandeforest

There are several slim connectors in use.
These are with power and used by small pc's including laptops and PC's like the Compaq Ipaq. A picture of the interface would be helpful. In any case I think there are only adapters available for some of the connectors because they are propriatary. So we need the exact physical spec. One angle may be that if you dissassembled the connector assembly inside the drive you might find a standard connector inside.

by dandeforest

followup: the so called slim ide has another name called ata 44 this is not propriatary and has various adapters available. This is used in the Compaq SFF PC referenced above. It is not a 7/8 inch 50 pin. The smaller 50 pin jobs are to carry audio as well as the 5 volts required by the drive.

by csmith

In the article by Detwiler, The adapter pictured, from Cablesnmor, will work.
Notice in the specs. that the DVD ROM only needs five volts.
It has that with the red lead. (Black is ground.)
As far as I know, there are no proprietary slim IDE interfaces.
Regards, Chris

by csmith

Forgot to mention. You loose the audio if you use a hard drive adapter. (As shown.)

by pc_kahuna

I have relied on Dirt Cheap drives in the past to build cables for some removable HDD?s. This cable sounds like some cables we use on the removable drives. The cable is a fifty pin SCSI that uses forty for the IDE and ten for the power. The web site is www.dcdrives.com and a phone for special orders is 800.786.1160. Hope this helped.

by nico rutte

The 50 pin cable is a standard IDE cable with 3 wires for audio 4 for power the rest is Ground.
The same manufacturer made all the cd drives for the iMac, there they used the same 50 pin cable. The cable connected without adapter to the mainboard of the iMac.
There have been people that use the first 40 wires of this cable and solderd them to a standard ide cable to connect other ide devices to the iMac.
For more info search the archives of the mac modification forum on www.macnn.com

by sam darroch

Hi,
I once actually purchased a pcmcia CDROM drive, which was basically a normal cdrom drive with a non-standard interface. The drive connected to the PCMCIA card via a 50Pin cable that sounds like the one your described, the same size and all. Perhaps you have been given the wrong drive.

by infosyst

To be totally honest about the 50 pin slim connector, it seems that you have been introduced to the new scssi-type interface drive connectors, and sadly , unless you have the right connection in your laptop, this will continue to be a little green eyed monster who hates everyone and everything.

by Former member

Found this connector:

Laptop Harddrive Adapter

2.5" to 3.5" Laptop Harddrive Adapter that goes into a Desktop Computer. This enables you to connect a laptop harddrive to a desktop computer

At this website:

http://www.laptopsforless.com/laptopaccessories.htm

Don't know if it will help.

by pooks

I contacted Matsushita on your behalf and received the following reply -->

Since this drive is 17mm height, we don't recommend you to install on desktop pc.
If possible, I recommend you to return the drive to the shop.

We need to know the OEM maker of your drive.
Please let me know a three-digit alphabet(C??) at the side of Voltage-Current in the rating label on the drive and a serial number under of bar code.

If you do want to install it, you can buy a conversion connector for CD-ROM (12.7mm/desk top) at pc shop.

You can use it for DVD Rom as interface is same.

----
H. Fukumoto fukumoto@rd5.mat.mke.mei.co.jp
Engineer/Techinical Support

Matsushita-Kotobuki Electronics Industries, Ltd.
Storage Products Division

<--

I hope this helps.

by estebandelatorre

The slim connector may be a 44 pin connector more common in the "laptop world". The interface is the same, they only enlarge the connector in order to add the power supply to the connector.
Below there is a diagram (pinout) of the ide interface plus the extension made.

IDE drive connector
Connector: 40 pin header
IDE Hard Disk Interface IDC-40 Male
pin assignment pin assignment
1 -Reset 2 GND
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8 Data 10
9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 GND 20 Key
21 (reserved) 22 GND
23 -IOW 24 GND
25 -IOR 26 GND
27 IO Chrdy 28 Ale
29 (reserved) 30 GND
31 IRQ14 32 -IOCS16
33 Addr 1 34 (reserved)
35 Addr 0 36 Addr 2
37 -CS0 (1F0-1F7) 38 -CS1 (3f6-3f7)
39 -Active 40 GND

Portables use a 44 pin IDE connector, which is the same as above plus:
41 +5V (logic)
42 +5V (motor)
43 GND
44 reserved

by gstavely

What you need is an adapter from 50pin to 44pin that should be the same as that used in the hard disk converter kit by cablesnmor.

This appears to comply with d2008r7b.pdf (AT Attachment-3 Interface ATA-3) from Technical Committee T13 (AT Attachment) www.t13.org, that outlines the ATA standard.

Refer Annex A 2.1 "Although there are 50 pins in the plug, a 44 pin mating receptacle may be used".

This discussion is closed to new replies.